The member shown below is a W12x87 (50ksi steel) is used as a beam-column in a braced frame, and must support the service loads and moments shown. both end is pinned and the column is subjected to moments about the strong axis. Investigate for compliance with AISC specifications. PD=160 k PL=240 k MD=60 k-ft M₂ = 60 k-ft Mp=60 k-ft M₂ = 60 k-ft 12f

The member shown below is a W12x87 (50ksi steel) is used as a beam-column in a braced frame, and must support the service loads and moments shown. both end is pinned and the column is subjected to moments about the strong axis. Investigate for compliance with AISC specifications. PD=160 k PL=240 k MD=60 k-ft M₂ = 60 k-ft Mp=60 k-ft M₂ = 60 k-ft 12f

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter6: Beam–columns

Section: Chapter Questions

Problem 6.8.3P

See similar textbooks

Similar questions

The member shown in Figure P6.6-4 is part of a braced frame. The load and moments are computed from service loads, and bending is about the x axis (the end shears are not shown). The frame analysis was performed consistent with the effective length method, so the flexural rigidity. EI, was unreduced. Use Kx=0.9. The load and moments are 30 dead load and 70 live load. Determine whether this member satisfies the appropriate AISC interaction equation. a. Use LRFD. b. Use ASD.
determine the member stresses of the truss shown. indicate if the stress in the member is in tension or compression. present complete and neat solutions. p1-30kN W-25kN/m P2=51kN AH Av Im P₂ Im P₂ Im P₂ Im Av W 1.6m
The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. When no load is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Determine the support reactions when the axial force of 400 kN is applied. 400 mm 400 kN B A992 steel 50 mm 800 mm 25 mm 2014-T6 aluminum alloy Section a-a -400(10*) N st (a)
The member shown in Figure has lateral support at points A, B, and C. Bending is about the strong axis. The loads are service loads, and the uniform load includes the weight of the member. A992 steel is used. Is the member adequate? a. Use LRFD. b. Use ASD.
4. 2L100x100x8 are welded together to form a box section as shown. It is used as a compression member to support a vertical load, P. The column is hinged on its top and fixed at the bottom (k = 0.70). Determine the largest allowable P that the column can carry if it has an unsupported length of 4m. Use A36 steel (Fy = 248 MPa) Properties of an L100x100x8: Area = 1551 mm² Moment of Inertia, Ix = ly 1448 x 10³ mm4 Centroid, x = y = 27.37 mm Ans. 343.02 KN 8 100 + 100 CIVIL ENGINEERING-SYEEL DESSION
snip
PLEASE ANSWER ASAP
4.3-4 Determine the available strength of the compression member shown in Figure P4.3-4. in each of the following ways: a. Use AISC Equation E3-2 or E3-3. Compute both the design strength for LRFD and the allowable strength for ASD. 15 HSS 10x6x ASTM A500, Grade B steel (Fy=46 ksi) 2/3
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. Steel E200 Gra A-600mm L-I m 2.0 m 0.6m 1.5 m D. V P-20 KN Aluminum E-70 GPa A-900mm L-1.5 m What is the axial load at aluminum rod in KN?
A tensile member consists of 2 ? 4 × 3 × 1/2 carries a service dead load of 50 k and live load of 100 k, as shown in Figure P13.15. The angles are welded to a 3/4-in. gusset plate, which is welded to a column flange. Design the connection of the angles to the gusset plate and the gusset plate to the column. The gusset plate is connected to the column by a CJP groove, and the angles are connected by a fillet weld. Use E 70 electrodes. The steel is A572. FIGURE P13.15 Welded connection for Problem 13.26. L4 x 3% 3-in. gusset plate Design welded connection 40⁰
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117