Answered: TENI Q P 160 KN Beam S Hinge 2m 2 m- R

Engineering

Civil Engineering

TENI Q P 160 KN Beam S Hinge 2m 2 m- R

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7. Distributed Loads A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load (b) Determine the reactions at the supports. wB = 4500 N/m WA = 1500 N/m %3D A -L 6 m-
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
a uniform bar 1 is connected to a tapered rod 2. both are subjected to axial loads as shown. if P=7 kN, determine the axial deformation of tapered rod 2 (in mm). indicate negative sign if compression
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
3) A load of 2,700 N acts on the machine part shown below. The machine part has a uniform thickness of 12 mm. Note: Point H will not be used in this problem and may be disregarded. a) Draw an FBD at showing the internal forces present at K. You may choose which side of the part to cut off. One method means you must find reactions at A and B. Choose the method that seems easier to you. b) Calculate the normal and shear stresses at point K (in MPa). [Ans. to check: = 0; ay = -10.89 MPa; Txy=-6.85 MPa] c) Draw the stress element at the point located at K. d) Calculate the normal and shear stresses if you rotate the element -20°. Draw a properly oriented stress element. 2,700 N 135 mm 60° C 50 mm 75 mm 50 mm X 40 mm # 12 mm 15 mm PH 40 mm OK y
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E Ук 1 kN 1m H F Figura 3. Cercha 3. 2.Determine the force in the elements ED, EH, and GH of the reinforcement (see Figure 4), and establish whether the elements are in tension or compres- sion. (Use the method of sections). Figura 4. Cercha 4. 50 kN 40 kN -2 m -2 m- -2 m- 1.5 m -30 kN 1.5 m B 40 kN 1.5 m
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-110 GPa 3P E=200 GPa 7m 3M 80mm 30 mm 30 mm 80 mm 30 mm 30 mm
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.