The member is supported by a pin at A and cable BC. Suppose that r = 3.5 m and the cylinder has a mass of 40 kg* Pt A :  Determine the tension in the cable BC. Pt B:  Determine the components of reaction force at the support A using scalar notation. Pt C: Determine the components of moment of reaction at the support A

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A: Draw the free-body diagram of the system.

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 184 lb, is…

A: There will be two reactions at thrust bearing and tension in the cable. Since Force F acts in single…

Q: Several blocks are resting on a simply supported beam. Determine the reaction forces. each block =…

A:

Q: The rigid body is supported by a hinge at A and a cable at C. The hinge resists 5.5m translation in…

A: Given data: The concentrated force acting at the center of the body is F = 260 N.

Q: The resultant of the three cable tensions acting on the flagpole is the force R acting vertically at…

A: Given:-        The resultant of the cable is acting on the force on the flagpole is:…

Q: The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A: To find the internal forces in members AB, BD, BC, and CD of the truss, we can analyze the forces…

Q: Calculate the reaction at the pinned wall joint and the tension in the cable for the system shown.…

A:

Q: 5 m 3 m A 8 m D D 40 KN 20 kN 8 m C

A:

Q: The member is supported by a pin at A and cable BC. Suppose that r = 3.5 m and the cylinder has a…

A: Consider the free body diagram of the given system as shown below. Here,

Q: The rod is supported by ball-and-socket joint D and cables AB, AC as shown in . Suppose that F = 700…

A:

Q: A bent pipe is connected by a thrust bearing and a cable as shown. If a Force, F = 195 lb, is…

A: Draw a diagram for the problem. Here, O is the origin, θ is the inclination of the force F with the…

Q: Find the cables' tensions and the reactions at ball and socket O.

A:

Q: en the end of the strut and the wall. Assuming that the entire weight of the sign is he strut, find…

A: Given: The weight of strut is, W1=425 N. The weight of the sign board is, W2=235 N. The angle…

Q: 1.5 m B 1.5 m 1m 5 m 3 m 1.5 m1 m* - 3 m

A: Drawing the free body diagram of the given system, Writing the co-ordinates of the point as follows…

Q: DENIMUI 2: This fuel pump uses the reciprocating action of rocker arm ABC. The arm is pinned at B…

A: Given data :- Force at point A (FA)= 60 N Force at point C (FC) =125 N To fond :- force acting at…

Q: A 400 N gas sign hangs from the end of a uniform strut BC. The strut is 4 m long and weighs 600 N.…

A: FBD of given figure   First we calculate the angle  tanθ=34θ=tan-134θ=36.86 Now consider clockwise…

Q: The traffic light shown below is supported by a system of cables. Points A and B are in a vertical…

A:

Q: A 7-ft boom is held by a ball and socket at A and by two cables EBFand DC; cable EBFpasses around a…

A: Given: The length of boom, L = 7 ft The force acting at C, P = 390 lb

Q: A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at…

A:

Q: A weight W= 120 kN is being supported by steel sections with force T, force F, and force C. The…

A: The problem is solved by forming vector equations for F, T and C. After that the equilibrium…

Q: 2. Find the forces acting at pins C and D of the given frame. worod slowly onto 22 m. - +3m -3 m 31…

A: To find: The forces acting at pins C and D of the given frame.

Q: 2: This fuel pump uses the reciprocating action of rocker arm ABC. The arm is pinned at B and is…

A:

Q: 2- Find the applied force by the hydraulic cylinder in the truck shown graphically using KS: 1cm=1m,…

A: Given Weight = 25 kN To find Force required to lift the weight

Q: 1.5 m 3 m F, x' 1m B

A:

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A:

Q: Members AB, AC, and AD intersect at point A. If a vertical force, F, is applied at point A, find the…

A:

Q: 3. Find the horizontal and vertical components of the forces at all joints. The reaction at point B…

A:

Q: Given: P, = 200 lb, P2= 500 lb Find: The forces in each member of the truss. P2 4 ft 3 ft 4 ft

A: The free body diagram of the truss is as follows: The moment about point A is as follows:…

Q: Q2/ The cable of the tower crane is subjected to 840 N force. A fixed base at A supports the crane.…

A: According to the information, we know that the force subjected on a crane is 840 N, fixed support at…

Q: necting W and point B passes over a frictionless pulleys. Fin Dlat noint A

A: given:

Q: Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0…

A: Given, W1 = 200 N

Q: =0.32 m A 0.24 m B C -0.4 m- Fi -0.4 m- D

A: Given data:Distance, a=0.32 mForces, F1=60 N and F2=9 NFind :Tension in the cable.The free body…

Q: B a b.

A:

Q: The resultant force of the three cable tensions that support the crate is R = 500j lb. Find T1 and…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.