The magnitude of the vertical reaction

Q: The simply supported beam in Figure below has a rectangular 3kN w = 1.5 kN/m cross section 100 mm…

A: Finding out maximum stress.

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: a. In your own words, what is the difference between a positive and a negative bending moment? b.…

A:

Q: 2. The maximum amount of solid waste collected per day for one week is presented below. All the…

A: Given, Municipal waste to energy combustion =100 tonsday

Q: An aluminum block show in Figure 9 is subjected to uniform pressure on all faces. If the chang ein…

A:

Q: Given: the IDF-curve shown in the Figure below, answer the following questions: a) Intensity for…

A:

Q: Q.15 A concrete pedestal is made of M25 concrete as shown below. The value of tana for this case is…

A: Given data- A concrete pedestal- M25 concrete, qo=6 N/mm2. To Find- The value of tan α.

Q: TANK TANK DATUM DATUM. DRAW AND LABEL VELOCITY HEAD DRAW AND LABEL PRESSURE HEAD (STATIC) Pressure…

A:

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: QUESTION 1 Determine the maximum moment in the cantilevered beam shown below, if A = 448 lb, B = 284…

A: Given Data  Find maximum moment in beam.

Q: 1. Locate the center of mass of the figure. The base has a mass of 45 kg/m2 and the vertical face…

A: Answer  We know that the co-ordinate of centre of mass with reference to y axis is given by y =…

Q: 1O N A GN

A:

Q: 0.5 in. B 1.8 in. P - 0.5 in. A 60° 1.8 in. 45° C

A:

Q: 6. Sample of standard brick, it's absorption equal to 17% and specific gravity equal to 1.65 the…

A: Given data: Specific gravity (G)=1.65 Absorption (w%)=17   To find : Porosity

Q: Please give correct answer

A: Given data : σX=100 MPaσY=80 MPaζXY=-30 MPa

Q: True stress-strain behaviour of a metal is given by the flow curve equation σ = 1750 €0.37 where o…

A:

Q: Determine the horizontal force reaction at joint 1. I l/ft A-9.12 in. 1-375 in. A= 103 in 1-285 in.…

A: To find the horizontal force reaction at 1

Q: Problem 3 Water flows through a pipe fitting that splits the total flow into three parts. The…

A: Given velocitin streaight pipe    v1=1 m/sdischarge at inlet  Q1=5 m3/secand area    A1=A2=1 m2and…

Q: ould the angle in this image be considered high, low, or canted?

A: there are different types of shots in photography some of them are  high-angle shots low-angle…

Q: 2 – Response of the two-degree-of-freedom system shown in to an initial displacements of uj = 0.915…

A: Introduction- The responses of a two system indicates that the systems requires two independent…

Q: Method of joints: Determine the forces in members EF, BF, and BC. 4.154 ft 1200 lb E 6 ft B 3 ft C 3…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: Calculate the ratio of maximum and minimum tensile reinforcement in rectangular reinforced concrete…

A: A rectangular reinforced concrete beam-Width b = 350 mm and depth d = 450mm Fe415 steel Cover = 50…

Q: 3.34 You are asked to design a horizontal curve for a two-lane road. The road has 12-ft lanes. Due…

A: The width of the lanes = 12 ftThe number of lanes in the road = 2 lanesThe maximum clearance from…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A: Answer  we are given h =1.5 ft rate of change of depth = -0.004 ft/s diamter of pipe d = 0.5 in…

Q: 4. Evaluale the peak flow for the following catchment: A=200 ha, runoff coefficient= 0.5,…

A: Given data : Runoff coefficient (C)=0.5Area (A)=200 haPrecipitation intensity (i)=1 cm/hr

Q: 1. How many significant figures does 0.000188 have? b. 2 2. How many significant figures does 275.00…

A: The significant digits in a calculation, such as 2.531, represent the number of digits recognized…

Q: 18. A 30-sec transit was used to measure a horizontal angle reading was 125 35' the average value by…

A:

Q: Highway curve has R = 800 m, I = 20° 00', and Pl station 3+290.600 m. Part A Determine degree of…

A: R=800mdegree of curvature=?

Q: Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1…

A:

Q: Set up the appropriate equation that is used to solve for the moment of inertia about the y axis.…

A:

Q: In the figure P30.5, identify the reactions. Show your diagrams. 20, KN 20, KN 20 KN 5. m A 15KN 12…

A: Given- A simple truss is given To find- support reactions

Q: Problem 1: Determine the magnitude of the resultant force per meter length acting on the…

A:

Q: create a hyetograph of the storm event. What is the maximum rainfall intensity? b) Plot the rainfall…

A: Area of dirt lot = 2 acretime steps = 0.5 hrrunoff coefficient =0.7time, intensity table is given…

Q: Q2. (a) Determine the maximum deflection of a cantilever beam at its free end subject to a uniformly…

A:

Q: 1. When the length or direction of a line within a traverse nissing quantities may be determined…

A: The correct answer is B. I.e they do not exceed two unknow quantities . Explain:  Because it leads…

Q: The design storm for a basin has the depth of rainfall for successive hours as 5.6, 7.6 and 5.2 cm.…

A:

Q: What is the most efficient curve fitting method in linear regression? Method of grouped averages O…

A: Curve fitting- It is one of the most powerful and widely used analysis tools in Origin. It examines…

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.