The machine is commenced to be heated at some point of a quasi-equilibrium manner till the temperature of air reaches to 900 K. During the manner the stress within the cylinder is held constant. Initially, 1kg air at 600K and at 150 kPa is contained in a piston - cylinder device. Air may be assumed as Ideal Gas below those conditions. a) Calculate the heat supplied to the air within the cylinder at some point of this process. b) Sketch the P[kPal-V[m³] diagram of the process. Indicate the path of the process. No want to explicit the extent of the air at the diagram. Please do best a difficult sketch.

The machine is commenced to be heated at some point of a quasi-equilibrium manner till the temperature of air reaches to 900 K. During the manner the stress within the cylinder is held constant. Initially, 1kg air at 600K and at 150 kPa is contained in a piston - cylinder device. Air may be assumed as Ideal Gas below those conditions. a) Calculate the heat supplied to the air within the cylinder at some point of this process. b) Sketch the P[kPal-V[m³] diagram of the process. Indicate the path of the process. No want to explicit the extent of the air at the diagram. Please do best a difficult sketch.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The gas expanding in the combustion space of a reciprocating engine has an initial pressure of SO bar and an initial temperature of 1623*C. The initial volume is 50000 mm' and the gas expands through a volume ratio of 20 according to the law pV constant. Calculate w and AU Take R= 270 J/Kg K and C, = 800 J/Kg K. Assume n 1.38
2) 3 mol of an ideal gas undergoes a process abc shown in the following PV diagram: P (10 Pa) 4 2 1 b la 2 V (10-³ m³) 3 4 5 The type of gas is unknown but UCD physicists measure its heat capacity to be 99.8 J/K when pressure is constant. Determine the total heat transfer for the process a b c. There are no phase changes. 6
Thermodynamics subject. Pleas show the complete and step by step solution. . A certain gas at 101.325kPa and 160C whose volume is 2.83m3 are compressed into a storage vessel of 0.31m3 capacity. Before admission, the storage vessel contained the gas at 137.8kPa and 240 C; after admission the pressure has increased to 1171.8kPa. What should be the final temperature of the gas in the vessel in Rankine?
2. Given a closed container of volume 1 L containing 50 g of helium gas, calculate the following: a. The pressure at T = 6 K, assuming that the gas is an ideal gas. b. The pressure at T of state. = 6 K, assuming that the gas obeys van der Waal's equation c. The pressure at T 6 K, assuming that the gas obeys the virial equation of state truncated after the second term. = d. The state of the fluid at T = 4.2 K. (Hint: 4.2 K is below T. and 50 kg/m³ is greater than p, @ 4.2 K.)
Consider a cylinder/piston system containing 2 kg of ammonia as saturated vapor at 20°C is cooled isothermally till its volume is half the initial volume. a. List assumptions to solve problem b. Find pressure, temperature and specific volume after the cooling process? c. Show process on T-v and P-v diagrams showing all phases and equilibrium curves
NOTE: Complete solution and show the derivation/cancellation of units. A steel flask of 0.04 m capacity is used to store Nitrogen at 120 bar and 20°C. The flask is protected against excessive pressure by a fusible plug which will melt and allow the gas to escape if the temperature is too high. A. How many kilogram of Nitrogen will the flask hold at the design conditions? B. At what temperature in °C must fusible plug melt in order to limit the pressure of flask to a maximum of 150 bar?
Q.5(a) 7 kg of air undergoes the cyclic process as shown in figure. Determine the work done for individual step and the cycle as whole.Figure-1[5]B. Tech. (I Sem.) CHE 102 (b) While working in chemistry lab (room temperature 30 oC) a student accidentally dropped a piece of cupper (12 g, 100 oC) in 30 ml water. Calculate the temperature of metal-water system at thermal equilibrium.Heat capacity of Cu = 0.54 J/ oC-gHeat capacity of water = 4.2 J/ oC-g
H2. A combustion facility is presumed to produce 9 Gigawatt-hours per year. Electricity price is 1.55 SEK per kWh. By raising the high temperature in the combustion facility från 373°C to 423°C to raise the efficiency. Calculate the repayment time for an investment of 1,730,000 SEK (operating cost staying the same). Assume that the facility is in a 12°C environment. (Clue: What expressions exist for the maximum thermal efficiency)
2) Two glass bulbs, one on the left with a volume of 2 liters and the other on the right with avolume of 6 liters, are connected to one another by a thin tube that is initially closed by astopcock. The bulb on the left has 0.1 moles of ideal gas, and the bulb on the right isevacuated. The system is in thermal equilibrium with the surroundings at 300K. When thestopcock is opened, the gas flows out to fill both bulbs. Calculate A for this process. If wewere to insert a propeller to extract work as the gas flows from left to right, what is themaximum amount of work that we could possibly extract?
Important: Indicate units of the properties. Fill up the table provided below with your answers. Include all calculations in another sheet/s as necessary. Note: The pressure values are absolute values unless specified. Determine the properties of H20 according to the following Table: CONDITIONS: ANSWERS: h= 1. Liquid at P = 17.5 Mpa and T= 200 C 2. Saturated liquid at T= 253.5 C S= 3. Steam with quality of 85 % at P = 6.1 Mpa h =
Given the pressure - volume diagram in figure below. Assume ideal gas undergo cyclic process. Path AB is adiabatic compression while path CD is adiabatic expansion. Also, paths BC and DA are isochoric processes. Ifthe value of y is 1.5, and the ratio of VilVy = 10 a. Calculate: QoalQsc b. Calculate Was assuming initial volume Vi= 2L and Pi = 1 atm. P C
c) ofR-134a at an initial pressure of 1.2 MPa is filled in a rigid container with a volume of 24.228 m³. The container is then cooled to 40°C. i. Determine the initial temperature and final pressure of the R-134a. Clearly show all calculations. Ikg ii. Show the process on a properly labelled pressure versus specific volume (P-v) diagram with respect to saturation lines.