the lower plate is being pulled at a relative velocity of 0.80 m/s greater than the top plate. The fluid used is water at 30°C. a) How far apart should the two plates be placed so that the shear stress is 0.25 N/m2? b) Calculate the shear rate

Q: the equivalent length of the exchanger as a complete unit (in terms of 20 mm diameter tube).

A: Consider a heat exchanger of length 12m, 10 close return bends and 15 x 90° elbows connected in…

Q: The force required to slip one layer of a fluid past another with a given velocity is * O Rate of…

A:

Q: ind modulus of elasticity of a brass rod of length 200 mm which is subjected to a tensile stress of…

A:

Q: Thousand kilograms of soya beans are composed of 18% oil, 35% protein, 10.0% moisture, and the…

A: Consider the below block diagram for the process of extraction of oil from soybeans:

Q: The laminar flow of a Newtonian fluid between parallel plates is illustrated in the below figure.…

A: Consider the laminar flow of a Newtonian fluid flowing between the two plates. The total gap between…

Q: A single crystal of a metal is oriented for a tensile test such that its slip plane normal makes an…

A: Given,

Q: . A tank with a capacity of 2m³ (2000 liters) is initially full of pure water. At time t = 0, salt…

A:

Q: drag force

A:

Q: (2020 psi), compute the critical resolved shear stress.

A:

Q: 3. A fine (thin) ring with a radius 50 mm is being pulled from the surface of water. If the ring has…

A:

Q: Q2)- A- From the attached figure showing the fluid type, model and equation, and calculate the shear…

A: Given data: Shear rate = 500 s-1

Q: Rate of movement of fluid passing one another. * O surface tension Shear O Rate of shear O Viscosity

A:

Q: Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0098 m.…

A: Shear stress = ζ =  μ dVdy  where,  μ = Viscosity oif oil = 0.04 Pa-s = 0.04 N. s/m2 Velocity…

Q: 3-foot-long, 8-inch-diameter cylinder inside a 25.8-inch-diameter tube at 3 feet per second. Fluid…

A: Given data: Length of pipe= 3ft Kinematic viscosity=0.006 ft2/s Constant velocity=3fps  Relative…

Q: Using the figure below, the lower plate is being pulled at a relative velocity of 3.14 m/s greater…

A: Given  Lower plate is being pulling a relative velocity of 3.14 m/s greater than top pate  Viscosity…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: 3.) A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension…

A: Given: Length of steel bar=100 mm=100×10-3mCross section of the steel bar=20 mm=20×10-3mForce=89000…

Q: Determine the hydrostatic force acting on the radial gate if the gate is 40 ft. long (normal to the…

A:

Q: A tensile stress is to be applied along the long axis of a cylindrical steel rod that has a diameter…

A: Given data: Diameter of rod = 0.015 m Change in diameter = 1.5×10–3 mm Value of Young’s modulus for…

Q: 10) For Newtonian fluids, the relation between the shear stress and the rate of deformation (du/dy)…

A: For Newtonian Fluid.  Shear Stress =  τ = μ dudy  where,   dudy = Rate of deformation or shear rate…

Q: Calculate the Gibbs energy, entropy, and enthalpy of mixing when 0.50mol C6H14 (hexane) is mixed…

A: Given that, The number of moles of C6H14 n1 = 0.5 mol The number of moles of C7H16 n2 = 2 mol…

Q: Use the accompanying phase diagram for carbon to answer the following questions.a. How many triple…

A: Note: Note: We are authorized to answer three subparts at a time, since you have not mentioned which…

Q: 1. Determine the maximum allowable vacuum that can be applied to a low-carbon-steel cylindrical…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: D

A: The flow of Fluid in Pipe

Q: Oil is allowed to flow in between two parallel plates. The distance between the plates is 0.0064 m.…

A:

Q: Magnitude of the resultant force of the coplanar system

A: We will calculate the magnitude of resultant force of the co-planar system by using Rectangular…

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: plate for glycerin Calculate the maximum laminar boundary layer thickness on a flat anematic…

A:

Q: 5. Rods AC and BC are used to suspend the 200-kg load. If each rod is made of a material for which…

A:

Q: The U tube shown is rotated about the left vertical leg at 30 rpm. The pressure at point A is…

A:

Q: For a parallel plate arrangement, it is found that when the distance between the plates is 2 mm, a…

A:

Q: With respect to Figure 1.1, consider the two parallel flat surfaces spaced 1 mm apart, with a…

A:

Q: For a parallel plate arrangement, it is found that when the distance between the plates is 5 4 mm, a…

A:

Q: separated from the plane with a film of oil of thickness 1.5 mm. The plate weighs 30kg and slides…

A:

Q: Velocity = 5 m/s Distance = 3in Thickness = 5 in Viscosity = 1 Pa.s Specific Gravity = 0.89 FIND THE…

A:

Q: Determine the size (diameter and height) of a thin cylindrical tank that can store 1000 m^3 of…

A:

Q: 3. A fine (thin) ring with a radius 50 mm is being pulled from the surface of water. If the ring has…

A:

Q: dynamic viscosity

A: Dynamic viscosity (μ) is the fluid property which explains the resistance of fluid flow on one layer…

Q: Define shear stress and it’s relation with dVx/dy for a Newtonian fluid

A: Shear stress is an important factor in the study of various types of fluids.

Q: 9. The fixed parallel plates kept at 80 mm apart have laminar flow of oil between them with a…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…