The loads acting on a 3 mm diameter bar atdifferent points are as shown in the figure:BA10KN|5kN2kN3kN1m2m3mIf Ewill be nearly.(a) 29.7 mm(c) 21.5 mm205 GPa, the total elongation of the bar(b) 25.6 mm(d) 17.4 mm

Answered: Image /qna-images/answer/c693fd56-006d-4652-8129-bebc8d23e031.jpg

Answered: The loads acting on a 3 mm diameter bar…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, T. S 65MPA and the angle of rotation of the free end limited to 11°. Use GS 84 GPa and Ga = 27 GPa. %3D %3D 75 mm Aluminum Steel 50 mm 2 m 1.5 m
Part II 1. The blocks shown in Fig. P-522 are separated by a solid strut which is attached to the blocks with frictionless pins. If the coefficient of friction for all surfaces is 0.20, determine the value of horizontal force P to cause motion to impend to the right. Assume that the strut is a uniform rod weighing 300 Ib. 200 lb _MATHalino.com 30° 400 lb 45° Figure P-522
PROBLEM 4 - A solid shaft given below is made from two segments: AC has a diameter of 15 mm and CB has a diameter of 10 mm. Determine the support reaction at point B and clearly statie its direction if it the shaft is fixed at points A and B and is subject to a torque 7' at point D. Take the shear modulus as 50 GPa. Write your final answer in the textbox below. Hint: J0.5ne, where e is the radius. 15 10 mm D. B. T 20 Nm 1m 0.5 m 2 m Wall
4 m 450 mm [s0 mn [50 mn 18 350 mm 50 mm Figure la Figure Ib Before a diver jumps into the water, helshe stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B8-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 mis?. Provide all steps of your working and solutions handwriten; include diagrams and coordinate systems. a. Determine the reactions at each support A and B. Use the variable w for the weight of the diver, include a free-body diagram.
SHOW COMPLETE SOLUTION AND SKETCH THE ILLUSTRATION
Example 21.18. A solid circular steel rod 6 mm in diameter and 500 mm long is rigidly fastened to the end of a square brass bar 25 mm on a side and 400 mm long, the geometric axis of the bars lying along the same line. An axial tensile force of 5 kN is applied at each of extreme ends. Determine the elongation of assembly. For steel E = 200 GPa and for brass E₁ = 90 GPa
EM6
The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. Assume b= 11 in, h = 3 in., r = 2 in, R = 3 in. Answer:lo-s=1 b R in.4 h
A simply supported steel beam is loaded with a uniformly distributed load and a torque. The beam has a U-shaped cross section, as shown. Determine the maximum normal compressive and tensile stresses caused by the acting loads. Express your answer in kgf/cm2 and in MPa.
Using the Portal Method determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 10 m P= 116 kN ЗР/2 G H 4m P 5m a b
As shown in the figure, a rigid beam with negligible mass is pinned at one end and supported by two rods. The beam was initially horizontal before the load was applied. Find the vertical movement of P if P=120kN.
A frame has dimensions and loadings as shown in the figure and parameter table. Determine the horizontal and vertical support reactions that the pins exert on the frame at A and C. Take postive directions to be to the right, and up. 080 BY NO SA 2021 Cathy Zupke parameter Force Ax Force Ay= Force Co = Force Cy= = W L₁ L2 A value 1 3 4.5 -L₂- units kN/m m m KN KN KN KN C B W

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The loads acting on a 3 mm diameter bar at different points are as shown in the figure: В A D 5kN 10KN 2kN 3kN Im 2m 3m If E = 205 GPa, the total elongation of the bar will be nearly. (a) 29.7 mm (c) 21.5 mm (b) 25.6 mm (d) 17.4 mm