The lengths of the half ordinates of an 80 m long water-plane commencing from forward as follows: 0, 3.6, 5.0, 5.3, 4.8, 0.5There is a 2.8 m long half ordinate right midway between the last two ordinates. Find the area of the water-plane.

The lengths of the half ordinates of an 80 m long water-plane commencing from forward as follows: 0, 3.6, 5.0, 5.3, 4.8, 0.5There is a 2.8 m long half ordinate right midway between the last two ordinates. Find the area of the water-plane.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Shown below is a trapezoidal canal of most efficient proportion. It discharges3m3/s of water. If n = 0.015 and S = 0.0021, solve for the value of d. use 3 decimal places
z=174 m A B z=152 m z=91 m T = and Op ≈pg əx (Pump) C F A pump is used to deliver water from a reservoir to a large tank for a flowrate of 1310 L/s at 20 °C. The connecting pipe connects the reservoir at B with a square-edged entrance. From B to C, the pipe is 760 m long and has three gate valves, four 45⁰ elbows, and two 90° elbows. Gage pressure at C is 197 kPa. From F to G, the pipe is 760 m long and contains two gate valves (Kg.-0.136), four 90° elbows (K90-0.51) and connects the tank with an exit (Kext=1). All pipe is 508 mm in diameter (D) and made by cast iron ( = 0.26 mm). 1) Calculate the average velocity of water in the pipe. 2) Calculate the gage pressure at F. z=104 m 3) If the pump's efficiency is 80%, calculate the power input to the pump. 4) If the shear stress can be calculated using the equation D Op hL major 4 0x L Calculate the average wall shear stress in section F-G. G H
USING DOUBLE INTEGRATION METHOD Consider 250 mm x 250 mm (bxh) mm section and e = 100000 MPa DETERMINE VERTICAL REACTION AT B Values:A = 9.4 MB = 5.5 MC = 10.6 KN/MD = 33 KN
Solve the value of Ely at x = 2m. 6 kN 2 kN/m 4 kN A 3 m -1.5 m-1.5 m O -106kNm^3 O -148.67kNm^3 O -124.83KNM^3 O 103.33kNm^3
1. Using Terzaghi's Bearing Capacity Equation, determine the soil allowable bearing capacity of a square footing. Use 2.0 as the factor of safety.
A trapezoidal channel is 0.5 m deep and the top width is 1.25 m. The bottom width and side slope of the channel are not given. Please help me find the bottom width and side slope of the channel. Please see the attached drawing.
A portion of a river is modeled with two reaches, A and B. Reach A extends from section1 to section 2 and has a length of 15000 ft, n = 0.07, S = 1 %, and Rh = 4 ft. Reach 2 extends from section 2 to section 3 and has a length of 17000 ft, n = 0.05, S = 0.5% and Rh = 5 ft. The hydrograph at Section 1 is (200, 300, 700, 600, 500, 400, 350, 300, 250, 225, 210, 205, 200), with a time increment, t of 10 min. Assume the initial discharge at downstream sections is 200. Using the Convex Routing Method, (a) route the hydrograph from section 1 to section 2 and then from section 2 to section 3.
What does the M=10 Kn.m represents? how do you call it? why on the Ma - 10 - (6.... why it is not Ma + 10. Please be specific I have doubts on this last steps of solution.
E= 29,000 ksi 10 kips IAB = 600 in IBD = 900 in A B 8 ft 12 ft 12 ft 1. Determine the vertical displacement at A. a. 0486 inches 1 b, 0.6402 inches 4 c. 0.7215 inches ! d. 0.5085 inches I e. None of the above 2. Determine the vertical displacement at C. a. 0.1907 inches t b. 0.2142 inches t c. 0.3193 inches t d. 0.1185 inches t c. None of the above
please answer with a neat solution and provide all answersA curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w = 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m.Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer.Determine the vertical component of the hydrostatic force (in N) acting on the gate, indicate the direction by putting an U for upward and D for downward after your numerical answerDetermine the magnitude (in N) of the hydrostatic force acting on the gateWhat angle (in degrees) does the hydrostatic force F make with horizontal?