The LC-3 ISA has been augmented with the following push and pop instructions. Push Rn pushes the value in Register n onto the stack. Pop Rn removes a value from the stack and loads it into Rn. The following figure shows a snapshot of the eight registers of the LC-3 BEFORE and AFTER the following six stack operations are performed. Identify (a)-(d).

The LC-3 ISA has been augmented with the following push and pop instructions. Push Rn pushes the value in Register n onto the stack. Pop Rn removes a value from the stack and loads it into Rn. The following figure shows a snapshot of the eight registers of the LC-3 BEFORE and AFTER the following six stack operations are performed. Identify (a)-(d).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
Not familiar with registers? indirect addressing method? What is the H? Explain the concept and answer below pls!
Describe shift Registers and its applications. Also explain the different types of data movment in shift Registers.
e example to each one of application of microprocess.. 2/ Write the contents of flag register after execute the following operation (AC)16 + (3B)16-
Which of the following is incorrect? Select one or more: In AVR, the data memory includes 32 general registers, 64 I/O registers and SRAM. In AVR, both program and SRAM memories have 8-bit data width. The AVR can read both an instruction and data from memory at the same time. The more registers we have for a CPU, the slower processing we can.
The state diagram of a Moore machine is shown below. This machine has one input (a), if we design its circuit by using two D-Flip Flops, which option will be the flip flops input equations? 9,9, = 00 01 1 10 Select one: O a. D1= Q1Q0' + Q1a, DO= Q1a' + Q1'a O b. D1=Q1'Q0 + Q1a' , D0=Q0a' + Q0'a O c. D1=Q1Q0' + Q1'a , D0=Q1' + Q0a' O d. None O e. D1= Q1'Q0 + Q1a' , D0= Q1a' + Q1'a
After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.
1- Explain the meaning and operation of CMC instruction ? 2. The Instruction Pointer is bits in length. a) 8 bits b) 4 bits c) 16 bits d) 32 bits
1. Write down 2- differences between Von-Neumann and Harvard architecture. 2. you are executing an instruction, SUB $s0, $s1, $s2 (address 0x20). Draw the datapath of this instruction when $s1=10, $s2=5. When are the stages in this datapath? Mark the components which are active in corresponding stages. 3. How to store(1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.
Microprocessor
Note: Please do not handwritten.also, don't write a lot of information.
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.