The journals of a shaft are 380 mm diameter, it runs at 105 rpm and the coefficient of friction between journals and bearings is 0.02. If the average load on the bearings is 200 kN, find the HEAT GENERATED per minute at the bearings. Badly needed asap. I will rate helpful. Thank you in advance.

Q: How to get mu=0.366. Show calculation fast.

A: Given : T1 = 30 KN T2 = 30000 KN n = 3 To find :  how to get coefficient of friction as 0.366

Q: The brake shown in Fig. 16-8 is 300 mm in diameter and is actuated by a mechanism that exerts the…

A:

Q: Grip. In the engineering design of handles (such as on manual and powered hand tools) and rails…

A: For solution refer below images.

Q: Consider a screw used in translation along with a 22 mm. inside diameter and 38 mm. outside diameter…

A:

Q: A screw jack has a thread with a pitch of 4 mm and diameter 22mm. The coefficient of friction is…

A: A screw jack withThe pitch of thread (p) = 4 mmThe diameter (d) = 22 mm The coefficient of friction…

Q: How much torque must be applied to drive the screw with the applied load in units of newton meters?

A: Here,  is lead angle,  is pitch,  is mean thread diameter.

Q: A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If…

A:

Q: and 45 mm respectively. The coefficie m for thread and collar are 0.15 and 0. rely: The machinist…

A:

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A:

Q: The critical speed of the shaft is 847.5 rad/s.

A: Given datathe diameter of the steel rod d = 24 mm = 0.024 mthe length of the steel rod l = 600 mm =…

Q: A conical pivot with angle of cone as 100° supports a load of 18 kN. The external radius is 2.5…

A:

Q: A leather belt of thickness 6 mm and width 80 mm connects two pulleys of 500 mm diameter and 900 mm…

A:

Q: A centrifugal pump delivers 1.27 m' of water per 1200 r.p.m. The impeller diameter is 350 mm and…

A:

Q: on c is 0, what is th

A:

Q: A square thread power screw has pitch diameter of 1.8 and lead of 1-in. Neglecting collar friction,…

A: Pitch diameterAnd leadSo the helix angle will be:

Q: Part B In the machine design the bed with a mass of 250 kg is moved by a lead screw which has a…

A:

Q: You have to build a box lifter, this will be made with a square threaded power screw. The power…

A:

Q: Q1) The V thread of a screw jack has a single start with out side diameter 40 mm and 6 mm pitch. The…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: A screw jack mechanism is to be incorporated into the machine as part of a levelling system. The…

A: Given data as per the question Diametre of jack =45 mm Thread pitch =6 mm coefficient of friction…

Q: A 340N force parallel to an inclined plane is required to just move a body of mass 50kg up the plane…

A: The objective of the question is to calculate the coefficient of friction and the force required to…

Q: ** Please label the question answers so I could understand it better! Thank you! Scenario: A chair…

A:

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A: Given data : Friction force=f Normal force=F'   Required : Coefficient of friction

Q: piston/cylinder setup contains air at 100 kPa,400 K that is compressed to a final pressure of 1000…

A:

Q: Find the power lost in friction assuming i)uniform pressure and ii)uniform wear,

A: The diameter of the vertical shaft is, D=100 mm The rotational speed of the shaft is, N=150 rpm The…

Q: A lead screw and saddle arrangement is used to lift a load of 200kg. The square thread has a pitch…

A: Power screws are the mechanical devices which are used for converting the rotary motion in to the…

Q: (A) If the power losses in Pelton wheel due to bucket friction is given by 1 POK (V, -u) where K is…

A:

Q: ne lead screw of a lathe has Acme threads of 40 mm outside diameter d 6 mm pitch. The screw must…

A:

Q: Calculate the torque.

A: The applied force is F = 89 cN = 0.89 NLength of crowbar L = 0.7angle = 80 degreeTorque is defines…

Q: The nominal diameter of a triple- threaded square screw is 50 mm, while the pitch is 8 mm. It is…

A: (i) To find : The torque required to raise the load. Given : The nominal diameter of screw is d=50…

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: A uniform push of 150N, applied at an angle of 30 degrees to a 20kg block which rests on a…

A: Given data: Initial velocity of block, u = 0 m/s. Final velocity of block, v = 6.5 m/s. Time, t = 4…

Q: A box that weighs 200N is sitting on an inclined ramp. The weight is assumed to act at the centroid…

A: (A) Draw the free-body diagram of the system.

Q: A screw jack has a thread with a pitch of 4 mm and diameter 22mm. The coefficient of friction is…

A:

Q: is pressed An electric disk sander (see Fig. against a surface with a force of 50 N. The coefficient…

A: Given: Force, F=50 N The diameter of the disk, D=200 mm The coefficient of friction between…

Q: Problem 1. Problem 1: A 1000lb block is in contact with a plane inclined at 20° to the horizontal. A…

A:

Q: a. 2et +5i – 4en +6j गँ en ↑ \ 23° i

A: The vector is

Q: You have to build a box lifter, this will be made with a square threaded power screw. The power…

A: The objective of the question is to calculate the depth of the thread, the width of the face, the…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.