The job of in shielded twisted pair is to carry away unwanted interference noise to ground. BNC connecter Ob. Drain wire. Oc. Four pairs of wires Od. RJ-45 Two or more consecutive bits in the data unit have changed after sending Multiple-bit error Ob. Pervasive error O C. Single-bit error Od. Burst error

Q: A 10 bit DAC has a Vref of 5.000 volts. What is 1 LSB or the smallest possible output change on the…

A: Given ==> ADC input = 0 - 5 V ADC output (10 bit) = 0 to 1111111111 in binary = 0 to 1023 in…

Q: The transmission signal coding method of TI carrier is called a. NRZ b. Binary c. Bipolar d.…

A: Given that: The transmission signal coding method of TI carrier is called a. NRZ b. Binary…

Q: Consider the synchronous circuit presented in the next figure. Assume the initial values in dhe FFs…

A:

Q: (c) In 8051, assume that the IE bit for the serial interrupt is enabled. Explain how this interrupt…

A: ANSWER:-

Q: Q1/To design a switching network that select one of 8 numbers ( X, Y, W, L, M, N,G,R) of 5-input…

A: There are 5 input data words. So we need 5 multiplexers. And there are total 8 numbers. Among which…

Q: What I/0 device number will activate this decode circuit? Remember that I/o device numbers are given…

A: Explanation: From the circuit diagram, the value of A7…A0 is 11011010. Here, the circuit executes…

Q: A 4X 1 multiplexer has O a. 4 output lines & 1 input line O b. 4 input lines & 1 output line O c. 4…

A:

Q: What are the pin assignments for a digital clock on a de2 board using Quartus II

A: The Quartus II Pin Planner helps you visualize, plan, and assign device I/O pins in a graphical view…

Q: What is baud rate in 8051?

A: Baud rate can be described as the number of symbols transmitted per second.

Q: Calculate the logical effort and parasitic delay of a one-bit ripple-carry cell adder

A: A ripple carry adder is a logic circuit in which the complete of each full adder is the convey in of…

Q: Write arduino code to gas. As the following condition a/ use the A5 analog pin b/when the smoke…

A: int LED1 = 12;int greenLed = 11;int buzzer = 10;int smokeA0 = A5;int smokeLevel = 600; void setup()…

Q: * choose the all correct answer please with me best wishes 16- A step-index fibre has a numerical…

A: A fibre that is flexible, transparent and made up of silica or plastics having a diameter slightly…

Q: multiplexer are hard wired as follows A3 =0 and A2 = A1 =A0 = 1, where A3 is MSB, and the select…

A:

Q: Task: 2 1. Design a Half Adder, HS, FA and FS circuits 2. Design a Binary to Gray code converter. 3.…

A: Half Adder Definition: Half Adder is the digital circuit which can generate the result of the…

Q: Sketch the output of the clamper network with sine waveform.

A:

Q: On our board the output signal on pin 8 of the LS04 is: IO/M ROMSEL WR ROMRD IORD RD

A: Answer:- The correct answer is "IO/M"

Q: In optical fiber, the core has a higher refractive index than the cladding. Select one: O True O…

A: In optical fiber the core has a higher refractive index than the cladding true or false.

Q: nge for

A:

Q: What is baud rate in 8051?

A: Answer:

Q: . Simplify the following Boolean function F, together with the don't-care conditions F(x,y,z)…

A: We are given a boolean function with dont care condition.  Note: In the image, final answer given is…

Q: Explain in two lines for each one 1- losses 2-Noise 3-Interference 4-Attenuation 5-Dispersion in…

A: Losses ,Noise , Interference , Attenuation , Dispersion in optic fiber

Q: Design an octal converter which has inputs of 4-bit BCD number (0~9) and outputs of oct and remained…

A: number A B C D s0 s1 s2 s3 s4 s5 s6 s7 s8 s9 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 1 0 0 0 0…

Q: You are required to make a carrier with the following details: Frequency- 1 hz/sec Amplitude - 2…

A: You are required to make a carrier with the following details: Frequency- 1 hz/sec Amplitude - 2…

Q: If the transmitter transfer the data using flow control with speed 1.2Mbps and the receiver receive…

A:

Q: 8051 Assembling program: design a program Count down from 9000 to 8000, show it on 7-segment LED,…

A: SUMMARY: -Hence, We discussed all the points.

Q: Briefly explain how to demodulate or recover the binary signal from BPSK. Explain with the aid of an…

A: Demodulation of a BPSK signal can be considered a two-stage process. Translation back to baseband,…

Q: Q3: Assume you have a main CLK with frequency of 16KHZ, design a frequency divider circuit that…

A: A frequency divider  can be constructed from jk flip flops by taking the output  of one cell to the…

Q: 2. Assume you have a button which has to be pressed constantly for 10s. If it is pressed constantly…

A: So here circuit Diagram is given below

Q: Write C18 program to send a byte of data serially to RC2 pin from PORTB. (MSB should go last)

A: The answer is given in the below step

Q: What is baud rate in 8051?

A: Baud rate can be described as the number of symbols transmitted per second.

Q: Question 6 How many control bits (i.e., select bits) are needed to control a Multiplexer with 512…

A: In digital logic and electronics, a multiplexer (MUX) is a device that allows you to select one of…

Q: What is the delay for a 64-bit 4-bit block carry-lookahead adder? Assume that each two-input gate…

A:

Q: In a multiplexer the output depends on its Select one: O a. Data inputs Ob. Select inputs Oc. Select…

A: Below I have provided a solution for the given question.

Q: A. What is the maximum and minimum output voltage at the analog output? Fill in the table below by…

A: In this task, we need to generate an analog periodic signal, y, using a 16-bit digital-to-analog…

Q: Q15/ Determine the baud rate necessary to pass a 4kbps binary signal using amplitude shift keying…

A: Hi there, Please find your solution below, I hope you would find my solution useful and helpful.…

Q: Q6. Construct a code to generate a square wave of 100 Hz frequency on pin PORTB.2. Use timer 0, 16…

A: Solution:--   1)The given question has required for the solution to be provided with the help of the…

Q: You manager has asked you to write a report to a customer who will be using the following digital…

A: It is the combinational circuit that determines the majority input among three inputs and outputs a…

Q: You have to design a synchronous 3-bit (CBA) up/down counter that can count up through the states…

A: Our task is to design the synchronise 3 bit up/down counter. We have to design the state transition…

Q: A 4 - bits PIPO register had 0000 as the initial bits. The register is to receive data and forward…

A: 1. Initially, the 4-bit PIPO register has 0000 stored in it.2. To transmit the 4-bit data 1111 using…