If the transmitter transfer the data using flow control with speed 1.2Mbps and the receiver receive the data through flow control with the speed 0.7Mbps, as an engineer what type of technique will you propose to solve the speed difference?

Q: If the baud rate (symbols per second) for a QAM signal is 1800 and the bit rate is 9000, how many…

A: Given the baud rate and bit rate, we need to find the number of bits per signal symbol.

Q: What is the propose of RST bit

A: Introduction: What is the propose of RST bit If the RST sender believes there is a problem with the…

Q: Data communication In a system with a bit rate of 3Mbps ,it is desired to send 3 bits at once…

A: In this question we have to solve for the given data. Calculate the levels, baud rate and bandwidth…

Q: A certain number of data bits (D) are encoded by a single pulse in one of 2D possible positions…

A: Answer: c PPM

Q: Whether VRC error detection method is used for single bit error or burst error.

A:

Q: Standard voice-grade lines are designed to carry frequencies in the range of: a. 1.5 MHz to 15…

A: Standard voice-grade lines are designed to carry frequencies in the range of:

Q: What is the maximum number of simultaneous calls in each cell in an IS-136 (D-AMPS) system, assuming…

A:

Q: Assume a 5 bit code is used for each symbol transmitted. If the bit rate is 50 MHz, what is the…

A: The relationship between the bitrate and baud is shown below. Bit rate = boud * number of bits per…

Q: What can be done to fix signal attenuation problems?

A: Signal attenuation is whe­n a signal's strength or amplitude decre­ases as it travels through a…

Q: What phrase is used to refer to the sum of the rotational delay and seek time?

A: Ans: The phrase that is used to refer to the sum of the rotational delay and seek time is called the…

Q: multiplexer are hard wired as follows A3 =0 and A2 = A1 =A0 = 1, where A3 is MSB, and the select…

A:

Q: Whether VRC error detection method is used for single bit error or burst error.

A: VRC can detect both single-bit and multiple-bit errors in a stream of data, making it a versatile…

Q: Explain the processes that are used in Time Division Multiplexing to deal with the varying input…

A: Multiplexing:  A multiplexer is the device that allows several devices to communicate over a single…

Q: 500Hz square wave signal. Set the input clock frequency CKL1 = 2.5 MHz, port addresses are…

A: Use 8524 Channel 1 to generate 500Hz square wave signal. Set the input clock frequency CKL1 = 2.5…

Q: What affects does delay skew have on the signal?

A: Intro What effects does delay skew have on the signal?

Q: Q1/A/ DM system is designed to operate 3times the Nyquist rate for a signal with a 3KHZ Bandwidth…

A: Provided the solution for both the above given questions, with detailed step by step explanation as…

Q: program a Python code for a two-band interference rate, please help

A: the program is an given below ;

Q: For 4 level ASK, If the bit rate is fb, the Baud rate is equal to: Select one: a. fb/2 b. fb c. fb/3…

A: In ASK, amplitude of carrier signal is varied to represent digital bits.  ASK stands for amplitude…

Q: Error detection and error correction operation cannot be applied on digital signals. Select one: O…

A: The given statement that error detection and error correction cannot be applied on digital signals…

Q: WDM is an analog multiplexing technique Select one: O True O False

A: True Wavelength Division Multiplexing (WDM) is an analog multiplexing Technique which is used to…

Q: What word is used to refer to the sum of rotational delay and seek time?

A: Introduction: It is called seek time on a movable-head system because it takes the head some time to…

Q: 1. Find the analog output voltage of a 5-bit digital to analog converter for any five inputs. Assume…

A:

Q: You are required to make a carrier with the following details: Frequency- 1 hz/sec Amplitude - 2…

A: You are required to make a carrier with the following details: Frequency- 1 hz/sec Amplitude - 2…

Q: QAM stands for(a) quadrature analysis method(b) quadrature amplitude modulation(c) quasi-amplitude…

A: Correct answer: D

Q: Exactly what is the term "multiplexing" used for?

A: Multiplexing: It is a method of delivering many signals or streams of information through a…

Q: difference between the si

A: given - In terms of the CE signal, what is the difference between the single-byte and burst modes?

Q: A medium uses QAM-16 scheme with 250 ksps and coding rate. What is the data transfer rate? Mbps

A:

Q: M-ary. Explain the

A: Disclaimer: As per guidelines, we can solve only one question at a time in multiple questions. Hence…

Q: etermine each output signal and draw the constellation diag 1. 8PSK TX Inputs: 000-111 Carier: cos u…

A: Brief Introduction: We have to write a code in Python that will make sure that the gcd of numbers…

Q: What is the average data rate of a signal transmitted at 36 kbauds and with 4 bits transmitted per…

A: No of bits transmitted => n = 4 The average data rata of a signal transmitted at 36 kbauds with 4…

Q: in a 4 bit adc if 0001 is 0.3125 volt then 1110 is

A: 0001 gives 0.3125. Means 1 count gives 0.3125 volt,

Q: Suppose we want to generate a PWM signal to toggle an LED every one milliseconds (1ms), which…

A: In the intricate world of microcontroller programming, generating Pulse Width Modulation (PWM)…

Q: What is the output signal voltage for a gain of 20 and input voltage of 20mV? O 10V O 4V O 400mV O…

A: Question. What is the output signal voltage for a gain of 20 and input voltage of 20mV? a) 10V b) 4V…

Q: How the sentence in CNF is written in logical agents ?

A: The answer is..

Q: Whether VRC error detection method is used for single bit error or burst error.

A: 1) VRC stands for Vertical Redundancy Check 2) It is also known as Parity Check. In this method, a…

Types of input and output devices

Input-output devices help in the functioning of a computer. An input device lets the user enter data into a computer. Common types of input devices are mouse, keyboard, joystick, and microphone.