The inverse of the matrix rs 31 Lio 6 r.2 331 Li 16) rs 31 L1.0 6) Option 1 Option 2 r.167 11 L 33 2) Option 3 Undefined O None of the above

Q: steel structure

A: Steel structures are widely used in modern construction due to their strength, durability, and…

Q: show full solution

A: Given data:The state of stress at a point is given by,To determine:The principal stresses, The…

Q: describe the five types of reservoirs and draw pressure-temperature phase diagram of each fluid

A: Types of Reservoirs : Single phase gas reservoir: It primary consist of recovery mechanism of…

Q: The value of surface tension is more at ______________________ .     50 oC     80 oF

A: So option (b) 80 oF is correct option.

Q: What is the V and M diagram? Thank you!

A:

Q: Warning-If not anything upto the mark, I'll report and dislike you. Draw figure of uniaxial state of…

A: Uniaxial State of stress-  this type of stress has only one principal stress. ie , when an object is…

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: Solution:

Q: Write short note on compression ratio

A: compression ratio

Q: Exus S.fd and Bomid? Draw YKN/m AX=0, 3m

A:

Q: Identify the material handling equipment   used for handling heavy casting in  foundry  Platform…

A: Bridge crane also known as overhead cranes are commonly used in the foundry industry to lift heavy…

Q: A thrust B journa 350N 0.25m B 0.35m 0.35m 0.15m 0.2m 0.Im P draw fbd

A: Draw free body diagram.

Q: Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20…

A:

Q: Water needs to be moved 11,000 horizontal feet with a flow rate will be 120 gallons per minute. The…

A: GIVEN Water needs to be flow =11000ft horizontal flow rate m=120gallon /min Maximum pressure…

Q: Draw the Ts diagram of the whole process

A:

Q: Calculate the critical design loads applied to the Stirling E ation and provide a stress analysis on…

A: In order to  find critical design load we need to equate thermal strss with reactive force per unit…

Q: 32 - (CLO-1) What is cold shut defect? a) Two portions of metal flow together but there is lack of…

A: Cold shut is a casting defect

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: 5m nas Taz ?

A: Given Data: Length of the beam, L=5 m

Q: Differen bending neaf possible ach t

A: for solution refer below images.

Q: The explantion is not clear

A: given : height of channel h = 10m width of channel w= 34m angle made by channel θ= 15o to find:…

Q: The general specification for production tubing is

A: After the casing has been run and cemented in place, production tubing is run into the drilled…

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: Estimate the heat loss from human body of 36 C temperature by convection and radiation. Consider the…

A: The heat loss from human body of 36oC temperature by convection and radiation is 304.875 W.

Q: 1 kN/m 1m

A: Shear force is an internal force in any material which is usually caused by any external force…

Q: Comparision between pulverized coal firing and stoker firing.

A: Pulverized coal firing and stoker firing are two common methods used for combustion in boilers to…

Q: Why should stress not exceed the material by design?

A: Every component is designed based on working stress which will acts on the component during its…

Q: Is the Hotelling Rule applicable to oil?

A: Hotelling's hypothesis, often known as Hotelling's rule, states that nonrenewable resource…

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: Why are the young modulus not used?

A: Tension in the wire is givenAnd working tensile strength is also gievn

Q: 3) Glazing bars are made up of a. PVC b. High speed steel c. Low Carbon steel d. Aluminium

A: option  (a) is correct( PVC)

Q: Q 13. A frame is said to be 'Perfect frame, if it followS certain relation betvoen number of members…

A: Perfect frame will not change when it is subjected to load with help of perfect number of members…

Q: 100 KH 20 KN/m B 2m C am RI

A:

Q: 2015.2 2.4713 27 0.031 2182.4 3.4800 29.33 0.044 2416.9 4.9900 32.48 0.063 2693.1 7.5062 36.19 0.095…

A: Given Data  To find “Since you have posted a question with multiple sub-parts, we will solve the…

Q: Fnd pressure at A? 100 m 500 m

A: Applying Pascal's  law:PA-1600*9.81*0.3+1000*9.81*.3-3000*9.81*0.1=PBPB is atmospheric…

Q: What is the ideal column?

A: An ideal column is one that is perfectly straight, made of a homogeneous material, and free from…

Q: Types of Supports and Beams

A: following is the answer to the above question-

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.