Problem 2:The information in an analog signal voltage waveform is to be transmitted over a PCMsystem with an accuracy of ± 0.1 % of the peak-to-peak analog signal. The analogvoltage waveform has a bandwidth of 100 Hz and an amplitude range of – 10 to + 10Volts.Determine the minimum sampling rate required.b. Determine the number of bits in each PCM word.c. Determine the minimum bit rate required in the PCM system.d. Determine the minimum absolute channel bandwidth required for the transmission of thePCM signal.

Given that, fm=100Hz Accuracy=0.1% Vin=[-10,10] a) As, fs,min=2fm=2*100=200 Hz Minimum sampling…

The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ± 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of – 10 to + 10 Volts. a. Determine the minimum sampling rate required. b. Determine the number of bits in each PCM word. c. Determine the minimum bit rate required in the PCM system. d. Determine the minimum absolute channel bandwidth required for the transmission of the PCM signal.

The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ± 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of – 10 to + 10 Volts. a. Determine the minimum sampling rate required. b. Determine the number of bits in each PCM word. c. Determine the minimum bit rate required in the PCM system. d. Determine the minimum absolute channel bandwidth required for the transmission of the PCM signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Regarding symbols used to illustrate transistors, a PNP transistor shows A. an arrowhead pointing into the transistor B. an arrowhead pointing out at the emitter. C. an arrowhead pointing out at the collector. D. no arrowhead
Explain the use of Metal Oxide Varistors MOVs
a) What is the advantage of increasing the switching frequency in switching converters (Buck, Boost etc.)and causes disadvantages to arise? b) General characteristics of IGBT and MOSFET, such as the current, voltage and switching frequency they can be producedCompare in terms of values. c) Output current and voltage ripples for a Buck-Boost type power converterWhat variables do (ripples) depend on? Explain.
In your own words, explain the Channel length modulation effect in MOSFET with a related graph and example circuit. [. a. b. In your own words, explain how MOSFET works as a Switch?
B6
b) i. ii. Comparing Silicon (Si), Silicon Carbide (SiC) and Gallium Nitride (GaN) power transistors answer the following: Which one is expected to have shortest turn-on, turn- off transition times and why? Which one would be your preferred device for operating at high temperature and high power when moderate switching frequency is desired?
I need the answer as soon as possible
How do microcontrollers handle Pulse Width Modulation (PWM) for analog signal simulation?
IV. In the circuit with a silicon transistor, as shown in the +Vcc Figure, if Viegic = 3.6 V, Vcc = 10 V, VLED = 2.3 V, RE = 270 2, B = 200, 1. identify the type of transistor in use and label the three terminals in the figure. logic input 2. find the base current. 3. find the collector current. 4. find the collector-emitter voltage. RE
Do not use AI.
Design BCD to Seven Segment Decoder. Draw circuit diagram using Basic Gate only.