The homogeneous 18-kg pulley is attached to the bar ABC with a pin at B. The mass of the bar is negligible. The cable running over the pulley carries a tension of 600 N. Determine the support reactions at A and C. (Convert the mass, m to weight, W. Use W = mg) 240 240 600 N 96 40% B 18 kg 600 N Dimensions in mm 120

The homogeneous 18-kg pulley is attached to the bar ABC with a pin at B. The mass of the bar is negligible. The cable running over the pulley carries a tension of 600 N. Determine the support reactions at A and C. (Convert the mass, m to weight, W. Use W = mg) 240 240 600 N 96 40% B 18 kg 600 N Dimensions in mm 120

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The ABC rigid bar is suspended by the BD rigid bar and by an A pin that connects it to the other ADE rigid bar. If the overhang load at point C is equal to 12kN, calculate the force on the BD bar and the reactions FA = √??2 + ??2, on pin A and the reaction FE roller located at point E. Disregard the weights of all the bars.
The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary? 2L 1 4L 3L 60° Answers: Ay i Dv = i Dx= i = B 60° 60° E 2L L 30⁰ L ! L D
Determine the reaction at E and the force in each member of the right half of the truss. State whether each member is in tension or compression
4. Determine the x, y, z components of reaction at the ball-and-socket joint A and the tension in each of the wires, if the load weighs 100kg. 1m 2m 1m D F A 1.5m B G 1m, 1m 1m.
Problem 3: Inputs: ● F = 1800 N P = 600 N (same as previous problem) a = b = 3 m (same as previous problem) c = 8 m (same as previous problem) The frame is comprised of two members. All joints are pinned. Compute the reactions at pins A and C, as well as the forces at pin B. P с a) Ax (Indicate left/right) b) Ay (Indicate up/down) c) Cx (Indicate left/right) d) Cy (Indicate up/down) e) Bx (no need to indicate direction since this is an internal force) f) a F B b C Net force in y-direction at pin B, using the FBD for bar BC. This is not necessarily By by itself. Again, no need for direction here.
Determine the magnitude of the pin force at A. Assume W = 520 Ib, a = 2.9 ft, b = 2.4 ft, r = 7 in. a C B A W D Answer: A = i Ib
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
Determine the reactions at the supportsand forces at hinge B acting on member CBAand the Tension on AE. Also, look for the x and y components.
The 300 N homogeneous bar AB, as shown, is supported by a pin at A and the cord BC. Determine the pin reaction at A on the bar AB. A -4 m 3 4 B 7
For the frame and loading shown, determine (a)the reaction at D, (b) the force in member BE.
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =