The helicopter view in the figure shows two people pulling on a stubborn mule. The person on the right pulls with a force of magnitude 89.4 N and direction of 0, = 70.0°. The person on the left pulls with a force F, of magnitude 85.3 N anc direction of 0, 80.0°. (a) Find the single force that is equivalent to the two forces shown. The forces are measured in units of newtons (symbolized N). 7.97 Use definitions of the sine and cosine to determine the components. Ni+ 165 V Nj (b) Find the force that a third person would have to exert on the mule to make the resultant force equal to zero. 180 Given that F, +F, +F, = 0, how is F, + related to the sum of F, and F,?Ni+ 87 Given that F, + F, +F- 0, how is F, + related to the sum of F, and F, Nj

The helicopter view in the figure shows two people pulling on a stubborn mule. The person on the right pulls with a force of magnitude 89.4 N and direction of 0, = 70.0°. The person on the left pulls with a force F, of magnitude 85.3 N anc direction of 0, 80.0°. (a) Find the single force that is equivalent to the two forces shown. The forces are measured in units of newtons (symbolized N). 7.97 Use definitions of the sine and cosine to determine the components. Ni+ 165 V Nj (b) Find the force that a third person would have to exert on the mule to make the resultant force equal to zero. 180 Given that F, +F, +F, = 0, how is F, + related to the sum of F, and F,?Ni+ 87 Given that F, + F, +F- 0, how is F, + related to the sum of F, and F, Nj

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8 kN Deturmim the anyle o S-thet the resulland force directead Vertical, Also find magnitud, of the resultan.? Hiw
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.8 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 88.86 MPa and its angle of twist is limited to 5.15˚. Use G = 80.77 GPa for steel and L = 462 mm. Round off the final answer to two decimal places.
The beam is subjected to a shear of V = 38 kN. Set w = 200 mm. 300 mm 20 mm A V B 2 -20 mm 400 mm 20 mm ▼ Part A Determine the web's shear stress at A. Express your answer to three significant figures and include appropriate units. Value Submit Part B μA Submit Value Units Request Answer | BΑ Determine the web's shear stress at B Express your answer to three significant figures and include appropriate units. Units www Request Answer ? 999 ?
1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL
Can you help me solve this problem?
5. Determine 8p and Og. Let q = 15 kN/m and L = 6m. 33
N06 The screw eye in Fig. is subjected to two forces, and Determine the magnitude and direction of the resultant forçe, NOST = N 001 = 1 عم کساب 2هلة القوست المر
Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a way that the shear stress in shaft does not exceed 100 N/mm2. If six bolt are used to join the flange and the bolt circle is 150 mm in diameter. Determine the diameter of the bolt if the permitted shear stress in the bolt is 80N/mm2.
The shaft is made of A992 steel and has an allowable shear stress of 95 MPa. When the shaft is rotating at 420 rpm, the motor supplies 11 kW of power, while gears A and B withdraw 7 kW and 4 kW, respectively. Determine the required minimum diameter of the shaft to the nearest millimeter. Also, find the rotation of gear A relative to C. (G=75 GPa) a. D=50.9589mm; 0.000004 rad b. D=50.9589mm; 0.0369 rad c. D=26mm; 0.000004 rad 300 mm d. D=26mm; 0.0369rad e. None of the above 300 mm B
Design the shaft (Find the diameter d). T = 2kNm; T, = 3kNm; L = Im; Tall = 58MP.. L d O 58mm O 30mm O 42mm O 95mm 81mm D 76mm
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
5. Determine 8g and 03. Let q = 15 kN/m and L = 6m. LA B L 3 3 3