19-20. The gear motor can develop 2 hp when it tums 450 rev/min. If the shaft has a diameter of 1 in.What is the torque developed by the power?A. 0.000707 lb-ftB. 23.34 lb-ftC. 127.83 lb-ftCS Delevina thamanimum shear strass deveiway to the shaft.A. 1426.60 psiB. 118.88 psi0.04323 psiD.280.11 lb-ftD. 0.0036 psimm diameter rivets.

Power developed by shaft = 2hp No. of turn=450rev/min Diameter of shaft=1 in To find Torque…

The gear motor can develop 2 hp when it turns 450 rev/min. If the shaft has a diameter of 1 in. What is the torque developed by the power? B. 23.34 lb-ft D.280.11 lb-ft C. 127.83 lb-ft A. 0.000707 lb-ft Detea tine (animum sheer stras devait the shaft. A. 1426.60 psi B. 118.88 psi 0.04323 psi D. 0.0036 psi

The gear motor can develop 2 hp when it turns 450 rev/min. If the shaft has a diameter of 1 in. What is the torque developed by the power? B. 23.34 lb-ft D.280.11 lb-ft C. 127.83 lb-ft A. 0.000707 lb-ft Detea tine (animum sheer stras devait the shaft. A. 1426.60 psi B. 118.88 psi 0.04323 psi D. 0.0036 psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The system consists of 60lb and 20 lb blocks A and B, respectively, and 5-lb pulleys C and D that can be treated as thin disks. Determine the speed of block A after block B has risen Sft, starting from rest. Assume that the cord does not slip on the pulleys, and neglect the mass of the cord. A
Compute for the: Vertical Reaction on A, kN Horizontal Reaction on A, kN Moment Reaction on A, kN-m
H.W.17/ This a butterfly valve (D = 12 ft) is used to control the flow in a 12 ft diameter outlet pipe in a dam. In the position shown, the valve is closed. The valve is supported by a horizontal shaft through its center. The shaft is located H= 60 ft below the water surface. What torque would have to be applied to the shaft to hold the valve in the position shown? HW 18/ The plan H Water Butterfly valve Shaft 30° Atmospheric pressure Diameter = D
2. Analyah below, Suffort B Support D setth = 2mm the bem Settes E h00 Gpa 80 kN 20 kN/m A.
Compute for the: Vertical reaction on A, kN Vertical reaction on B, kN
Reaction on the beam
moment eqvation . Draw rhear p soive for hear and Mo184 emt, Consider 2. MDment DiIagram. 30 KN 4.0 m 4.0m ĝ. Compute the moment iner tia require ment to a beam rhow n 아 below Concidering bending moment , Iļ 4. 70 KN IM 5.O M IL 1.76 KN/M 6.0 M
21 Drive the Max Hydraulic horspower u Mox HHP. and Max ImPact force May. IF When the flaw rate Located between Minimum and maximum flow Pate,and the hydraulic hers Pawer of Pump is Copstant.
6.12 ft L D G_4.24 ft F C 0.88 R K T 12.12 + 1 LT-- A 45° j4 ft K ftl 4.24 ft Referring to the figure shown. Determine the horizontal force due to the water acting on the cylinder per foot of its length.
Ex 18: For. the. Cofferdam Shown.in the. Eig. below.; find: O The Capacity of the Pumprefuired.. ®. Pore Water Pressure at Points. A, B, C. O Factor of. Sahty against. PiPing.. @ What height of Water. outside the Cafferdam Would. give E.S -2. 25 Esat:= 18 -KN /m 士 -C- %3D -5 K= 2.6 x 1o. m/sec 4m 2.25m Datum
need asap :(