The gas tank is made from A-36 steel (oyield= 300 MPa) and has an inner diameter of 1 m and a wall thickness of 30 mm. If the tank is designed to withstand an internal pressure of 6 MPa, determine the factor of safety against yielding using the maximum-shear-stress (Tresca) theory. Lütfen birini seçin: a. 1.61 b. 3.00 c. 2.76 d. 2.22 e. None Sonraki sayfa

The gas tank is made from A-36 steel (oyield= 300 MPa) and has an inner diameter of 1 m and a wall thickness of 30 mm. If the tank is designed to withstand an internal pressure of 6 MPa, determine the factor of safety against yielding using the maximum-shear-stress (Tresca) theory. Lütfen birini seçin: a. 1.61 b. 3.00 c. 2.76 d. 2.22 e. None Sonraki sayfa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
Please help me
مقاومه HW2
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld. O 611 ksi O452 ksi O 653 ksi O 3.77 ksi O 495 ksl
Question 7 of 20 2 Pa The nigid bar of weight W= 100 KN, is carried by three rods as shown. The mechanism is arranged such that it is symmetrical. Refer to the table for the properties of each material Steel Bronze Coefficient of linear expansion 11.7x 10 18x 100 Moctulus of Elastioty 200 GPa 83 GPa Area, A 500 mm 900 mm Length L 1.00 m 1.60 m Steel Steel Bronze A. W
Thank you in advance, note it ask for stress a B
How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used. * Sm 40 RN 35 AN
None
A spherical pressure vessel has a 1.33-ft inner radius and 0.19-in. wall thickness. If the working tensile stress of the material is 5594psi, determine the maximum allowable internal pressure (in psi). Add your answer
Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case.
How many 10-mm diameter rivets is needed to fasten member BF to the gusset plate at B if the member BF has thickness of 8 mm and the working stresses are 30 MPa for shear in the rivets and 45 MPa for bearing due to the rivets.
The solid bar ABCD consists of three segments subjected to three (3) torsores as shown below. If G = 11.6x10 ^ 6 pounds / inches. Determine: 1. Where the maximum shear stress is recorded and what is its magnitude. 2.The angle in radians that rotates point D.