The fuel in high-efficiency natural-gas vehicles consists primarilyof methane (CH4). (a) How much heat is producedin burning 1 mol of CH4(g) under standard conditions ifreactants and products are brought to 298 K and H2O(l) isformed? (b) What is the maximum amount of useful workthat can be accomplished under standard conditions bythis system?

Q: One mole of an ideal gas at 10 atm pressure is contained in a vessel at 300K. The gas is expanded…

A: Given data: Number of moles of ideal gas = 1 mol P1= 10 atm T1 = 300 K

Q: It is desired to produce 250 kg / h of steam methanol at 150ºC and 1 atm from liquid methanol at…

A: The schematic process flow chart for the given process is prepared as:

Q: Problem 4: A Nigerian kerosene has an API gravity of 41.2, aniline point of 55.6°C. Estimate the…

A:

Q: 4. A heat exchanger is to be designed to raise the temperature of 10 kmol/hr of ammonia from 300K to…

A: Given, molar flow rate , n=10 kmol/hr=10×1000 mol3600 s=2.78 mols  Initial Temperature, T1=300 K…

Q: Oil initially at 15°C is heated in a perfectly mixed stirred tank (as shown below) by saturated…

A: Given data: T1=15°CT2=35°CTsteam=130.5°Cm.in=m.out=450 Kg/hm=2250 kgh=600000 J/°C/hrCp,oil=2000…

Q: give sample problem with a solution regarding the interchange of radiations between two parallel…

A:

Q: En a heat exchanger with steam outside the tubes, a liquid gets heated to 45°C w ts flow velocity in…

A: This problem is based on heat transfer.  The initial flow velocity is given by v= 2 m/s. The…

Q: CO2 is sold commercially in steel containers at 60 bar. The gas is leaking through the outlet valve…

A:

Q: Handwrite everything in the picture Uses of Bomb Calorimeter Bomb calorimeters are devices which are…

A:

Q: Sol. Since AU = 0, then the heat on segment ab is QH = TH In | The heat on segment cd is QC = - TC…

A: A Carnot heat engine is a theoretical engine that operates on the Carnot cycle. This system may be…

Q: 410 g of ethane (MW = 30 g/mol) was burned completely using 1,600 g of oxygen gas (MW = 32 g/mol).…

A: Given data: Amount of ethane = 410 g Amount of O2 = 1600 g T1= 40 0C T2 = 85 0C Heat capacity of…

Q: Q1. Considera Shell and tube heat exchanger constructed from a 0.0254m OD tube to cool 6.93 kg/sec.…

A:

Q: A 1g cube of metal A at 80 °C is placed in 100 cm³ of water and causes a 0.333 °C rise in water…

A: For metal A: Given, mass of the metal A, mA = 1 g The initial temperature of the metal, TA,0 = 80 °C…

Q: Ammonia's melting point is 196 K and its boiling point is 240 K. an experiment, 50.00 g ammonia was…

A: As for the given problem , the latent heat value aren't provided , the values are obtained from…

Q: 4.9-2. Cooling Oil by Water in an Exchanger. Oil flowing at the rate of 5.04 kg/s (Cpm = 2.09 kJ/kg…

A: Given Data The flow rate of oil (mh)=5.04 KgSThe specific heat capacity of oil (Cph)=2.09…

Q: conditions shown in the diagram, how much heat is saved if the air supply is 5,000 cfm and the wheel…

A:

Q: 11. A constant pressure of 10 Pa is applied to a 1 kg parcel of dry air with initial tem- perature…

A: PressureP=105Pam=1kgT1=10∘C=283KV2=0.75m3To find:Work doneW

Q: Ethylene gas and steam at 400 degree C and 1 atm are feed to a reaction process as an…

A:

Q: Q1/A power plant operating on Camot cycele that produces (500MW). I tumed out that this represents…

A: Hi and thanks for the question. Since you have posted multiple questions and didn't specify which…

Q: Cooling a Gas Mixture. It is required to cool a gas mixture composed of 75 mol % N₂, 15 mol% CO₂ and…

A: A mixture of gases is cooled in a heat exchanger.

Q: 50 kg of a mixture containing 20 wt.% ethanol and the rest water is loaded into a flash drum where…

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: Q1: (A) kg of air is compressed causing its temperature to increase from 25K° to 100K°. If the…

A: Given, Heat capacity of air, Cp = 0.917+14.32×10-5T-51.29×10-9T2 mass of air, m = 1 kg Initial…

Q: 1- Evaporation differs from distillation: a- The vapor rarely is a single component; b- The vapor…

A: According to company guidelines, I can only solve the first three MCQs. please upload the remaining…

Q: An aqueous food solution at a temperature of 18 deg C contains 6% solids (by mass) and is to be…

A: Given, The mass fraction of solids in the feed, xF = 0.06 The mass fraction of solids in the…

Q: A. Show that dp Determine the final density and enthalpy of the water: P (a) if it is heated to 50°C…

A: Initial conditions are given as, Also,

Q: (2). We take one mole of ideal gas at standard temperature and pressure and add to it 500J of heat…

A: An isobaric process is a thermodynamic process in which the pressure remains constant. ∆P=0 The…

Q: Over a 0.1 m X 0.1 m sheet at 175°C, air flows at 25°C and 1 bar with a velocity of 1 m/s. Calculate…

A:

Q: For a certain specific heat capacity at varying temperature, the following data are gathered: a x…

A: Given, Specific heat capacity with constants are a×103 = 22.76b×105 = 30.13c ×108 = 25.20d ×1012 =…

Q: CO₂ is sold commercially in steel containers at 60 bar. The gas is leaking through the outlet valve…

A: Introduction Ideal gas equation In this equation, P refers back to the pressure of the proper gas, V…

Q: Q2): It is required to heat 10000 bbl/ day of crude oil (as given in case study of Lecture3) in a…

A: Mass rate of crude oil=10000 lb/day temperature change T1=220 °F to T2=622 °F  NHV of refining…

Q: 4.) Steam undergoes an Isentropic process where it is initially at 1.30 MPa and 200 C then it…

A: Given, The initial pressure, P1 = 1.30 MPa The final pressure, P2 = 0.75 MPa The initial…

Q: starting with the chocked mass flow rate equation for isothermal ideal gas flow discharging through…

A: The mass flow rate of the orifice is considered to be equation one. The coefficient of discharge…

Q: Calculate the final temperature if 450 Kw of heat was added to a stream of air at 25 °C and 20 kg/hr…

A: Heat gained or lost by the system is based on the Law of conservation of energy. The heat lost by…

Q: Two equal masses of graphite C and Cu were heated by absorbing 20 KJ, which one of the following is…

A: Given that   The specific heat capacity of various elements are given. Specific of C = 0.711 J/g-k…

Q: 1. Fit the data for the following function: Cp=aT³ +bT2+ cT +d Where T is in C 2. Then calculate…

A: The first trial data is substituted to obtain the d value. The second, third and fourth trial data…

Q: 1) Heat capacity of hydrogen is given in terms of polynomial functions of temperature: Cp…

A: Given heat capacity of hydrogen in terms of polynomial functions of temperature is…

Q: A flue gas is analyzed to contain (dry basis): 11.6% CO2, 6.8% O2, 0.5% CO and leaves the boiler at…

A: Given information

Q: Q2): of 32 "API crude oil is fed to an atmospheric distillation unit, the following products were…

A: crude oil  volume=1200 BPD product from distillation tower (in table) steam mass flow rate=567…

Q: Calculate AH;f

A: To produce change in temperature by a unit degree of a molecule, the amount of heat required for the…

Q: calculation (a) the hydrocarbon form as (CxHy) (b) the adiabatic flame temperature.

A:

Q: The molar heat capacity at constant pressure for CO2 is 36.61 J mol-1 K-1. How much heat in J is to…

A: Given data: Molar heat capacity at constant pressure (Cp) for CO2=36.61 J.mol-1.K-1…

Q: A problem indicates that the enthalpy of a compound can be predicted by an empirical equation Ĥ(J/g)…

A: Given H = -30.2 + 4.25T +0.001T2