The frame ACD is hinged at A and D and is supported by a cable that passes through 5) a ring at B and is attached to hooks at Gand H. Knowing the moment exerted by the portion BH of the cable about the diagonal AD is 90 N-m. Determine the force exerted on the frame by portion BH of the cable. 0.35 m 875 m 0.s25 m 0.75 m 0.75 m 05m 05m

Q: 0.4 m A 4.8 m 0.6 m 5.6 m 4.8 m x PROBLEM 3.51 A farmer uses cables and winch pullers B and E to…

A:

Q: Determine the magnitude of the moment of the force F about point O

A:

Q: An 12-lb force P is applied to a shift lever. Determine the moment of P about B when a is equal to…

A: Given Data P=12 lb

Q: The 8-ft wide portion ABCD of an inclined, cantilevered walkway is partially supported by members EF…

A:

Q: P=65 N 02: The 25-N Force Pis applied perpendicular to the portion BC of the bent bar. Determine the…

A: As moment is force multiply by perpendicular distance, we will calculate by same procedure. Given…

Q: A precast concrete wall section is temporarily held by two cables as shown. Knowing that t cable BD…

A: Find the position  coordinates  for the points B and DThe position vector of BDThe position vector…

Q: Forces P and Q of magnitude 250 N and 500 N, respectively, are applied on the bent board as shown.…

A:

Q: The hood of the automobile is supported by the strut AB, which exerts a force F = 24 lb. What is the…

A:

Q: Problem 3 Determine the moment exerted by cable AD about point C. X 1 m 1m 0 D C 3 m FAD B = 100N A…

A: Given data  Force in cable AD = 100N Find the moment of force about point  C

Q: b#5 Determine the total moment about the point B P. 15 in. D 60° 1o lb. in 7 in. B

A: Solution: From the above figure, sin60=BE7BE=6.062incos60=CE7CE=3.5in Then, Distance…

Q: A gate is held in the position shown by cable AB. If the tension in the cable is 6.90 kN, determine…

A:

Q: A force of 90 N is applied on a lever AB as shown in the figure. Knowing that the lever is 225 mm…

A: given force F=90Nlength of lever AB L=225mm=0.225mmoment about point B is MB=13.5Nmα= angle makes by…

Q: To lift a heavy crate, a man uses a block and tackle attached to the bottom of an I-beam at hook B.…

A: Given Data: The coordinates of the points A and B are:

Q: The flanged steel cantilever beam with riveted bracket is subjected the couple and two forces shown.…

A: To determine the reaction at A.

Q: An 10-lb force P is applied to a shift lever. Determine the moment of P about B when a is equal to…

A:

Q: H.W. Determine the resultant moment produced by the forces about point Oof the cases below. S00 N F…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: QUESTION 5 Knowing that the tension in cable AC is 1065 N, determine the moment about each of the…

A:

Q: Q 2) For the figure shown, what is the moment about A of the force exerted by the cable BC. Knowing…

A:

Q: A single force P acts at C in a direction perpendicular to the handle BCof the crank shown.…

A: From the given diagram, the coordinates of point C are (250 mm, 200 mm, 200 mm). Write the position…

Q: Q/3 A rectangular plate is supported by hinges A and B and by cables DF and DG. Knowing th the…

A:

Q: Problem 1.3 -A force F is applied to one end of a cable of length L. The other end of the cable is…

A: Given Data The length of the wrench is: L=200 mm The angle of force acting on the wrench is: α=30°…

Q: 3.30 For the truss and loading shown, determine the resultant of the loads and the distance from…

A: For the given truss To determine  Resultant of the loads and the distance from point A to its line…

Q: A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular…

A:

Q: that F = 100.0 N, determine the moment with which it is screwing (a) The OA tube at O. (b) The OB…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.