QUESTION 5 Knowing that the tension in cable AC is 1065 N, determine the moment about each of the coordinate axes of the force exerted on the plate at C. 360 mm 920 mm lo 600 mm 900 mm O Mx = -576 N-m, My Mx = -243 N-m, My = -576 N-m, Mz = +405 N-m = -405 N-m, M2 = -243 N-m %3D My = -405 N-m, My = -243 N-m, M2 = +576 N m O Mx = -576 N-m, My = -243 N-m, M, = +405 N-m

QUESTION 5 Knowing that the tension in cable AC is 1065 N, determine the moment about each of the coordinate axes of the force exerted on the plate at C. 360 mm 920 mm lo 600 mm 900 mm O Mx = -576 N-m, My Mx = -243 N-m, My = -576 N-m, Mz = +405 N-m = -405 N-m, M2 = -243 N-m %3D My = -405 N-m, My = -243 N-m, M2 = +576 N m O Mx = -576 N-m, My = -243 N-m, M, = +405 N-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the moment about A, C, and F for the forces acting on the link shown below. Point C is at the center of B and D. Take F1 = 49 N, F2 = 16 N, F3 = 21 N, F4 = 28 N, F5 = 41 N and F6 = 24 N. F1 F5 4m 7 F6 6m 4m A B F2 F3 Solution: (i) Moment about A in Nm is (ii) Moment about C in Nm is (iii) Moment about F in Nm is C I 10m E F4 60°
A force P (200 + R)i + (250+ R)j + 300 k N, is acting at origin of the co-ordinate system, and a moment M = (10+ R)i + (100 - R)j + 30 k N-m, is acting at (0.5,1.0, -0.5) m from origin. Replace the given force system by equivalent wrench system, and determine the point where the axis of wrench will pass through x-z plane. (R = 41)
PROBLEM 2: ● Find the moment about A, B, C,D and E of the forces shown below. AB = 8m, BC = 10m, CD = 3m and AE = 6m. 70N SON 40N E D 20N B Y 60° 60N C 30N
Express and identify the resultant of the two forces and one couple shown acting on the shaft angled in the x-z plane. Assume F = 490 lb, M = 470 lb-ft, a = 5 in., b = 12 in., 0 = 22° 10 a -M j+ i !k) lb-in. F. Answer: M = i F Ꮎ ! i+ i 5302
For the same problem given in Part A, if the support at B creates a reaction force Bx and By as shown, determine these reaction forces. Assume B is located at 3 m from the origin O along the z-axis Z X By 3 m O 6 m 3.5 m Bx G 3.5 m A 2 m Y
Problem 3 Determine the moment exerted by cable AB about point C. The force in the cable is 700 lbs. 6 ft X Z 4 ft B 4 ft D 6 ft 6 ft
(1) In this experiment, you will start with a chamber (pressure vessel) filled with air at ambient conditions. a. In the first part of the experiment, this pressure vessel is quickly filled with compressed air until the pressure inside the vessel is as much as ten times that of the ambient condition. What do you think will happen to the temperature inside the chamber during the filling process? Will it increase, decrease or remain the same? Why? b. After the vessel is pressurized, you will let it equilibrate for several minutes. What will happen to the vessel temperature during this time? Why? c. You will then open the vent valve and allow air to leave the chamber until the pressures are equilibrated (vessel pressure returns to the ambient pressure condition.) While the tank vents to the atmosphere will the temperature inside the tank increase, decrease or remain the same? Why? (2) If the pressure vessel is not truly adiabatic, how will the predictions from Question 1 change?…
#2 Member OA is restrained from twisting by cable AC. All dimensions and coordinates systems are as shown. Write an expression for the unknown Tension in cable AC (hint: use unit vectors!) D y 160 mm 100 mm B 40 N-m 190 mm A 60° 220 mm X
Also, determine the y-component and z-component of the moment about point O. Express your answer in units of kN-m.
asin The moment of the force F=120-lb about the point O in Cartesian vector form is. F= 120 lb 1 ft> 4 ft 2 ft Select one: O a. Mo = 200j- 400k O b. Mo= -200j + 400k O M, = -200j - 400k C. 9a M.-200j + 400k
The horizontal force F = -Fi acting on the handle of the wrench produces a component of the moment along the OA axis (z axis) of the pipe assembly of M, = {4.4 k}N•m. Both the wrench and the pipe assembly, OABC, lie in the y-z plane. Suggestion: Use a scalar analysis. y-z (Figure 1) Part A Determine the magnitude of the force F. Express your answer to three significant figures and include the appropriate units. HA F = Value Units Figure < 1 of 1 Submit Request Answer Provide Feedback 0.8 m 0.2 m 135 0.6 m
Express and identify the resultant of the two forces and one couple shown acting on the shaft angled in the x-z plane. Assume F = 500 lb, M = 490 lb-ft, a = 8 in., b = 22 in., 0 = 12° -M Answer: M=1 İ+ i 12.57 k) lb-in. -21.52 İ+ i 300