The following three parallel-connected three-phase loads are fed by a balanced three-phase source: Load 1: 250 kVA, 0.8 pf lagging Load 2: 300 kVA, 0.95 pf leading Load 3: 450 kVA, unity pf If the line voltage is 13.8 kV, calculate the line current and the power factor of the source. Assume that the line impedance is zero.

The following three parallel-connected three-phase loads are fed by a balanced three-phase source: Load 1: 250 kVA, 0.8 pf lagging Load 2: 300 kVA, 0.95 pf leading Load 3: 450 kVA, unity pf If the line voltage is 13.8 kV, calculate the line current and the power factor of the source. Assume that the line impedance is zero.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The output of the balanced positive-sequence three-phase source in the figure is 64 kVA at a lagging factor of 0.8. The line voltage at the source is 256/3 V. power (Figure 1) Find the magnitude of the line voltage at the load. Express your answer in volts to three significant figures. Figure Balanced three-phase source 0.04 2 w 10,2 2 m 0.04 0.2 0 0.04 w 10,2 2 Balanced three-phase load 1 of 1 |VAB= Submit Request Answer Part B V Find the total complex power at the terminals of the load. Express your answer in volt-amperes to three significant figures. Enter your answer in rectangular form. S= Submit Request Answer VA
The Figure shows a balanced Y-A 3Ø circuit. The phase voltages of the Y-connected source are V, = 11020°, V, = 1102 - 120° and V. = 1102120°, Volts. The line impdedances are Z,=10+j5 Q each. The impedances of the A-connected load are ZA = 75+j255 N each. Determine: Line Currents, Phase Currents (load), Power drawn by the load. Ve ZA Vb
A balanced three-phase, negative sequence, Y-connected generator is connected to a three-phase balanced Y-connected load. The generator has an impedance of 1.5-j1.25 Q/phase. The impedance of the line connecting the generator to the load is 2.5+jl1.25 0/phase. The phase "B" load voltage is 1520° kV. The impedance of each phase of the Y-connected load is 60-j80 Q/phase. Calculate phase voltages \(V_{an}\) at the generator. \(V_{an}=\) Volts
Calculate the line currents in the following 3-phase balanced system (at load). The voltage source connected to the load is in the form va (t) = 100.coswt and phases b and c are offset by 120 degrees. Does a current flow through the delta connection? Prove it and show it with calculation. LA ICA A IAB 20/45° Ω VCA VAB 20/45° B - 20145° N VBC Ic
B) A three-phase, 50 Hz, A-Y connection. The line voltages of primary and secondary are 3300V and 400V respectively. The line current on the primary side is 12A and secondary has a balanced load at 0.8 lagging p.f. find: i. The secondary phase voltage and line current. The output power.
SAP ID =8925
Which of the following statements is corect, Magnitude of the phase voltage is greater than the line-to-line voltage by a factor of /3 Line-to-line voltage lags the phase voltage of the load by 30 ° In Wye connection balanced load, line currents are equal to the phase currents of the load. In delta balanced load connection, no current flows through the neutral wire
A 3-phase transmission line supplies A-connected load z as shown in figure. The negative sequence current of phase R will be R Y B 25 20⁰ 25 / 180° Z ww Z Z
Please help will sure upvote ..........
A balanced three-phase load requires 1.8kW and power factor 0.5. If the line voltage at the terminals of the load is 230 V. the magnitude of line current is: Select one: a. 7.82 A O b. 9.03A O c. 15.65 A O d. 4.51 A
A Y-A system has source voltages of 415Z-105° V on its a-phase and 415Z135° V on its c-phase. Determine the type of sequence of this system. If this Y-A system has source, line and load impedances of 6/45°2, 15 - j25 Q and 102230° Q respectively, obtain (a) The line currents (b) The load currents (c) The load voltages (d) The complex powers supplied by the sources
Two single-phase loads are connected in parallel, where load 1 is 4.7 kVA at 0.87 lagging power factor, and load 2 is5.2 kWat0.79lagging power factor. The load combination is connected to a voltage source of220VAC,50 Hz. a) Find the total complex power