The following figure shows a horizontal conduit formed by two tubes and different diameters discharging freely into the air, in the second tube there is a valve that regulates the flow. For Q = 50 Its/sec and the valve half open with Ko = 5.6 Calculate the height h if the water temperature is 15° с A H L = 250 m. L = 120 m Ligeramente fundición asfaltada Redondeadas =10" L = 100 m $=8" B

The following figure shows a horizontal conduit formed by two tubes and different diameters discharging freely into the air, in the second tube there is a valve that regulates the flow. For Q = 50 Its/sec and the valve half open with Ko = 5.6 Calculate the height h if the water temperature is 15° с A H L = 250 m. L = 120 m Ligeramente fundición asfaltada Redondeadas =10" L = 100 m $=8" B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
11.20 3. Parallel Pipe Three pipes are in parallel with a total head loss of 20.3 m. The pipe data are pipe 1 2 3 L, m 100 150 80 d, cm 8 6 4 €, mm 0.24 0.12 0.20 €/d 0.003 0.002 0.005 The fluid is water, p = 1000 kg/m³, and v= 1.02 x 10-6 m²/s. Calculate the total flow rate in cubic meters per hour, neglecting minor losses.
Four reservoirs have pipes that meet at a common junction. Their characteristics are as follows: (see table) If the friction factor, f = 0.015 for all pipes, determine the following: a. discharge of pipe Ab. discharge of pipe Cc. discharge of pipe D
14
Workshop 1: Answer the question. Consider the diagram. The tank in figure 3, contains water at 10°C and has a level of h = 15 feet, the pipe consists of 950 m with a diameter of 2.5 inches, if it contains 5 elbows, 15 unions and two globe valves at 80 %. and 52% open. !! Calculate: a) The outlet flow. 工 2 ft エ Figure 3.
answer is given just give the solution and right answer.
subject: hydraulics engineering
A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter = 1cm) is directed straight up. If the air gage pressure inside the tank is 200kPa, solve the theoretical volumetric flowrate out of the nozzle assuming no losses. AIR 20 m O 0.0020m^3/s O 0.0022m^3/s O 0.0031m^3/s O 0.0027m^3/s
A roof tank supplies water as shown in Figure 1. Calculate the minimum height (H) in metre required to maintain a 1.5 m head pressure and 1.0 l/s flow rate at the point of discharge. Given the following data: G.I. pipe diameter d = 25 mm Friction factor f = 0.009 Loss coefficient: ki = 0.2 k2 = 10 Gate Valve Globe Valve Elbow k3 = 2 k4 = 0.5 k5 = 20 Entrance loss at tank Water meter 116 FIGUEE I I un lom'
If the flow between the two reservoirs is 3 L/s, calculate the difference in elevation between the water surface. Both pipes are made of stainless steel. Use a value of 1 x 10-6 m²/s for the kinematic viscosity of water. D = 50 mm L = 6 m D = 25 mm L = 6 m 2
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
Solve last three parts where density of fluid is 900kg/m3