The following figure shows a confined aquifer with two piezometers measuring pressure head at two different locations 450 m apart. The aquifer has a uniform thickness of 3.2 m and a hydraulic conductivity of 7.2x10³ cm/s. Assume the width of the aquifer into the page is 10 km, and the flow is one dimensional from left to right. Compute the total flow in the aquifer. 450 m -Piezometer Elevation: 86 m Elevation: 845 m 3.2 m Confined Aquifer

The following figure shows a confined aquifer with two piezometers measuring pressure head at two different locations 450 m apart. The aquifer has a uniform thickness of 3.2 m and a hydraulic conductivity of 7.2x10³ cm/s. Assume the width of the aquifer into the page is 10 km, and the flow is one dimensional from left to right. Compute the total flow in the aquifer. 450 m -Piezometer Elevation: 86 m Elevation: 845 m 3.2 m Confined Aquifer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A confined aquifer of 10-m thickness and 16.43 m/day hydraulic conductivity is fully penetrate by a pumping well of 0.5 m radius operating at Q=425 m³/day. Determine the drawdown under steady-state conditions in a) the pumping well and b) 50 m away from the well. Take the radius of influence of the pumping well as 300 m.
.A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure (not drawn to scale) Piezometer P 55.2m Piezometric Surface Aquiclude Aquifer Aquiclude Piezometer Q L = 2500m 34.1m The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydraulic conductivity of 80 m/ day and its effective porosity is 0.If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is
6. Two observation wells have been constructed in the confined aquifer shown below. If the flow rate (Q) is 0.01 m³/hr/unit width, Porosity, n= 0.26, effective porosity=0.23 and and compressibility of aquifer matrix is a = 10-8 ms2/kg: compressibility of water, B = 45.8 x10 11N/m² i. ii. lii. 20 m K₁-15 miday 300m K₂-7 K₁-10 m/day Determine K2 what is the effective hydraulic conductivity (K) for the system Calculate transmissivity and Storativity
A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the figure (not drawn to scale) 55.2 m BT Peizometer P Reference Datum Aquiclude Piezometric Surface Aquiclude Peizometer Q L = 2500 m 34.1 m ונטוב SOM The heads indicated by two piezometers P and Q are 55.2 m and 34.1 m, respectively. The aquifer has a hydrau- lic conductivity of 80 m/day and its effective porosity is 0.25. If the distance between the piezometers is 2500 m, the time taken by the water to travel through the aquifer from piezometer location P to Q (in days, round off to 1 decimal place) is
A confined aquifer has a source of recharge as shown in the figure. The hydraulic conductivity of theaquifer is 40m per day and its porosity is 0.25. The piezo metric head in the two wells with 13.25 mapart are 65m and 60m respectively from a common data. The average thickness of the aquifer is25m and the average width is 4km.a. Compute the rate of flow through the aquifer in cu.m per day.b. Compute the seepage velocityc. Compute the time of travel from the head of the aquifer to a point 4 km downstream in days.
a. For Figure 2 below, calculate the effective hydraulic conductivity for flow parallel and perpendicular to layering. Show your work. Explain the difference in values. Figure 2 sand layer; K = 1 m/d; thickness = 5 d 10.5 m clay layer; K = 0.000001 m/d; thickness = 0.5 m sand laver: K = 1 m/d; thickness = 5 m b. Figure 3 below shows the effects of groundwater refraction, assuming that groundwater flow in the top layer is almost horizontal i.e., a = 89.8°, what is B and what can you say about the flow in the clay layer? a a K, b B K Figure 3.
Soil layers are shown as the right figure. Given: H₁ = 2 m, k₁ = 10-4 cm/sec H₂ = 3 m, K₂ = 3.2 x 10-² cm/sec H₂ = 4 m, K₂ = 4.1 x 10-5 cm/sec Estimate the ratio of horizontal equivalent hydraulic conductivity and vertical equivalent hydraulic conductivity, i.e., k./k₂ T * H₂ H₂ a. 152 Ob. 270 O c. 140 O d. 225 k₁ k₂ k3
Q 2.An aquifer has following different formations, their thickness and Hydraulic conductivity are given below. Assume that each formation is isotropic and homogeneous. Compute both the equivalent horizontal and vertical hydraulic conductivities Formation Thickness (m) Hydraulic Conductivity (m/day) 1 8.5 19.7 8 26.4 12.5 33.1 16 34.8 10.5 19.5 15 29.2 16.5 26.9 18 34.6 16.5 27.3 18 18 21.5 44.7 26 36.4 27.5 32.1 25 46.8 28.5 55.5 34 52.2 30.5 38.9 36 51.6 33.5 33.3 32 40 41.5 41.7 43 56.4 37.5 46.1 40 61.8 43.5 48.5 45 73.2 41.5 46.9 50 56.6 44.5 63.3 55 70 52.5 62.7 56 70.4 53.5 83.1 53 70.8 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34