The following beam has an exposure class of N. f'=35MPa, fy=400Mpa. Assume 15M stirrups. Find the Mr and check the following beam meets all code requirements using the method of your choice. 6-25M 400 mm 600 mm

Q: The figure shows the soil profile at a site where you plan to lower the water table. You have…

A:

Q: An HSS 16 x 16 x 1/2 (A = 28.3 in?, twall = 0.465 in, r, = ry 6.31 in) with F, = 46 A 18 ft long…

A: Data Given: Column section=16×16×12Gross area =A=28.3 in2b=16 in,  t=0.465 inry=6.31 inL=18 ftFy=46…

Q: Consider the following beam ABC, loaded as shown in figure. The cable passes over a small…

A: For given arrangement,W= 10 kNTo find the maximum shear force in the beam AB

Q: Find the approximate height of water upstream of the dam or the headwater in meters, such that an…

A: Considering the diagram below:

Q: At full draw, an anchor applies a pull of 130 N to the bowstring of the bow as shown in the figure.…

A: Ans1)Pull=130KnThe diagram is given below-

Q: Draw SFD and BMD of following beams and also check the adequacy of the selected steel beam section.…

A: To draw SFD and BMD for the given beamCheck whether W18X60 is adequateNote: As per the guidelines,…

Q: what conclusions you can draw from this graph

A: Consider the given graph. From the graph, it can be seen that as the hardness of the steel…

Q: Define the term Classification Tests.

A: The classification test for the soil is performed to distinguish the property and type of soil. The…

Q: discharge pipe in which the velocity is 2.40m/sec. At point A in the suction p pressure is - 40kPa.…

A: Given:- diameter =200mm  discharge pipe dimater =150mm  To find:- Power

Q: Answer

A:

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

A:

Q: Situation 12- Wooden planks 300 mm wide by 100 mm thick are used to retain soil soil exerts a…

A:

Q: Briefly describe the CSI Specifications?

A: CSI stands for the Construction Specification Institute. CSI has introduced a common format for…

Q: Situation 5 - The steel strut transmits a compressive force P = 75 kN as shown in the figure. The…

A:

Q: What is “excess” scale (esp. CaCO3) a concern for water utilities? (answer in three to five…

A: Excess scale specially Calcium carbonate is a concern for water utilities due to 1. increased…

Q: What is the main requirement for a BIM approach ?

A: Brief Concept Introduction- BIM- BIM stands for Building Information Modeling. BIM is a very vast…

Q: 1. A liquid has a specific gravity of 0.8. Determine its specific weight (in N/m³) and density (in…

A:

Q: A pump helps bring oil (SG = 0.8) to reservoir D from reservoir A at 235 liters per second. The…

A:

Q: Road construction specifications

A: The asphalt is in road construction, wherever it is used as the glue or binder mixed with…

Q: PLEASE ANSWER ASAP!!! PROVIDE FBD FOR THE PROBLEM. ANSWER THE FOLLOWING CORRECTLY BY PROVIDING CLEAR…

A:

Q: A residential development of 280 houses is being planned. Assume that the American Water Works…

A: Average daily water production=n*1320 Here n is number of houses is given,n=280 and the average…

Q: 80 kPa el. 12 m 120 kPa el. 7m A pressure gauge at elevation 12m at the side of a tank containing a…

A: We know that: PB=PA+ρliquid gh

Q: Situation 8- The cantdever beam shown is fixed at C. Given: L = 25 m, a = 0.3 m P = 40 kN, w = 8…

A: L= 2.5 m, a= 0.3 m , P-40 kN, w= 8 kN/m   Calculate the moment (kN-m) at C=?  Calculate the torque…

Q: Determine the reactions at the supports for the frame in Q. 2. E is constant. 3k/ft 10k Inc = 800…

A:

Q: Find the axial load resistance of the tied short column shown below and check all code requirements.…

A: b = 350 mm h = 350 mm fc = 30 MPa fy = 400 MPa Main bars, 8-20mm

Q: A 10' 8 kips B 10' 0.25 kips/ft Draw a shear diagram C 10' 15 kips 15 k D 25 kip *ft (c) How many…

A: An overhanging beam with uniformly distributed load, two point loads and a moment acting at the free…

Q: wing that is related to transportation engi

A: A working sketch or blueprint is one that is based on explanations. It's finished with a detailed…

Q: Piston A has a cross sectional area of 1400 mm² While that of piston B is 1000 mm-. B is higher than…

A: Given Data Area at A=1400 mm2 Area at B=1000 mm2 Pressure=Force /area Pressure at B PB +ρgh = PA F/A…

Q: PROVIDE DETAILED SOLUTIONS AND INDIVIDUAL FBD. ANSWER CORRECTLY AND TABULATE.

A:

Q: Hello, do you have any solution for Problem 2?

A:

Q: PROBLEM: A built up section of A992 steel is made from plates fully welded together. The flanges…

A:

Q: What are anthropological hazard emergency response.provide detailed information.

A: Brief concept introduction- Anthropological hazard- It occurs when a potentially dangerous agent…

Q: Situation 10-A 25 m simply supported girder of a bridge is crossed by a standard H. loading…

A: Length of simply support beam = 25 m  Load carrying of two wheel load  of 142.4 KN and 35.6 KN which…

Q: A layered soil deposit is of dimension 3m x 2m x 3m. There are three different soils, each of 1 m…

A: To find the quantity of flow

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.