The flow along a closed curve is called circulation. With reference to circulation and vorticity, choose the correct statements from the statement(s) given below. Circulation is given by r=v. If the flow is taking place in the x-y plane then circulation for an elementary rectangle is given (du dr) ax ay dedy where u, v are the velocities in x and y directions respectively. by r- Vorticity is equal to the rotation component about an axis perpendicular to the plane in which the area is lying. All of the above

The flow along a closed curve is called circulation. With reference to circulation and vorticity, choose the correct statements from the statement(s) given below. Circulation is given by r=v. If the flow is taking place in the x-y plane then circulation for an elementary rectangle is given (du dr) ax ay dedy where u, v are the velocities in x and y directions respectively. by r- Vorticity is equal to the rotation component about an axis perpendicular to the plane in which the area is lying. All of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flow is described by the flow field of V = A(1 + Bt)î + Ctyĵ, where A=1 m/s, B=1 s¹, and C=1 s². The unit for the coordinates is meters. a. Plot the pathline that passes through the point (x=1 m, y=1 m) at time t=0 b. Compare the streamlines through the point (x=1 m, y=1 m) at time t=0, 1, and 2 s c. Calculate the acceleration at time t=0 along the streamline passing the point (x-1 m, y=1 m) at time t=0
6 Consider a fully developed laminar flow of a fluid through 8027 m long and 4 cm diameter horizontal and circular pipe. The dynamic density and the viscosity of the fluid are 1252 kg/m³ and 0.3073 kg/(m.s). The velocity profile at a cross-section is given by: u(r)= 6[1 − ( 7 )²] - m/s Where r is the axial distance from the centre and R is the radius of the pipe. Determine the following: (i) (ii) the maximum velocity at a cross-section of the pipe, Umax the average velocity at a cross-section of the pipe, Vave the volume flow rate, Q (iv) Reynolds number, Re (v) friction factor, f (vi) head loss, hi (vii) pressure loss, AP (viii) pumping power required, (ix) for the same pumping power, the percentage decrease of the flow rate if the pipe is inclined 10° upward (assume the head loss, hò, calculated in part (vi) does not change) Useful formulae: 64 f Re h₂ = f ( =) ( 2² ) 2g =
Make it
Fully laminar flow in cylindrical pipe Consider the steady, viscous flow of Newtonian (dynamic viscosity), incompressible(density ρ ) fluid through a pipe with a circular cross-section (radius R) under the constantpressure gradient in the x-directionwhere x1 and x2 are two arbitrary locations along the x-axis, and P1 and P2 are the pressures at those two locations (note that we adopt a modified cylindrical coordinate system here with x instead of z for the axial component, namely, (r, , x)). Coordinates of fluid velocity in the cylindrical coordinates are (ur , u, u). - Show that the velocity field inside the pipe is (0, 0, u) and (photo)- Show that the flow discharge Q is (photo)
Water is flowing in a rectangular channel with a base of 4.0 ft. The velocity gradient from the bottom of the channel to the water surface is given by the equation: v=3.5y^0.6 Where y is the distance from the bottom of the channel. The total depth of the flow in the channel is 3.0ft. a) Graph the velocity profile from the bottom of the channel to the water surface. B) Calculate the flow rate by integration. The first step is to draw a cross-section of channel and on that cross-section, Draw on your figure an elemental area DA that you will then ise in the equation: Q=integral V.dA
Consider the flow of water through a clear tube. It is sometimes possible to observe cavitation in the throat created by pinching off the tube to a very small diameter as sketched. We assume incompressible flow with negligible gravitational effects and negligible irreversibilities. You will learn that as the duct cross- sectional area decreases, the velocity increases and the pressure decreases according to V1A1 = V2 A2 and P1 + ρ V21 / 2 = P2 + ρ V2 2 / 2respectively, where V1 and V2 are the average velocities through cross-sectional areas A1 and A2. Thus, both the maximum velocity and minimum pressure occur at the throat. (a) If the water is at 20°C, the inlet pressure is 20.803 kPa, and the throat diameter is one-twentieth of the inlet diameter, estimate the minimum average inlet velocity at which cavitation is likely to occur in the throat. (b) Repeat at a water temperature of 50°C. Explain why the required inlet velocity is higher or lower than that of part (a).
Fluid mechanics question