The floor system of an apartment building consists of a 4-An.-thick reinforced concrete slab resting on three steel floorbeams, which in turn are supported by two steel girders, asshown. The areas of cross section of the floor beams andthe girders are 18.3 in.2 and 32.7 in.²,and 32.7 in.², respectively.Determine, the total load carried by girder AE.Unit weight of Steel: 490 lb/ft³; concrete: 150lb/ft³Live load for Apartment Bldg. : 40 psfSteel girderW= 32.7 in.Steci flop beam(A = 18.3 in.)I25 11DSteelcolumnFcon rete slab2 at 12 ft = 24 11

Answer Let us draw the free body diagram of the girder AE Total load carried by the girder AE =…

The floor system of an apartment building consists of a 4- An.-thick reinforced concrete slab resting on three steel floor beams, which in turn are supported by two steel girders, as shown. The areas of cross section of the floor beams and the girders are 18.3 in.2 and 32.7 in.2, respectively. Determine, the total load carried by girder AE. Unit weight of Steel: 490 lb/ft³; concrete: 150lb/ft³ Live load for Apartment Bldg.: 40 psf

The floor system of an apartment building consists of a 4- An.-thick reinforced concrete slab resting on three steel floor beams, which in turn are supported by two steel girders, as shown. The areas of cross section of the floor beams and the girders are 18.3 in.2 and 32.7 in.2, respectively. Determine, the total load carried by girder AE. Unit weight of Steel: 490 lb/ft³; concrete: 150lb/ft³ Live load for Apartment Bldg.: 40 psf

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultima strength fc = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t+= 16 mm lx = 266x105 mm4 ly = 45 x 105 mm4 fy = 248 MPa Wb = 90 kg/m fy = 248MPa Calculate the service floor live load (kPa) each beam can sustain in bending under allowable stress design method. Select the correct response: 7.05 2.91 C CUN 2.21 1.92
Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultimate strength f'c = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t = 16 mm lx = 266x106 mm4 ly = 45 x 106 mm4 fy = 248 MPal Wb = 90 kg/m fy = 248MPa If each beam is laterally braced by the concrete slab, calculate the allowable bending strength using safety factor of 1.67. Select the correct response: 175.17 248.79 235.94 394.03
Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 133 MPa and 195 MPa, respectively. The cross sectional area of the two wires are 492 mm² for AB and 214 mm² for AC. Wire AB is inclined 27-degrees with the horizontal and wire AC is inclined 47-degrees with the horizontal. Give the largest weight W (kN) that can be supported by the wires?
The floor system shown carries a live load of 4.80kpa live load and 100mm thick concrete slab. Let point A and Point C be pin and roller support, respectively and determine the: A. Maximum factored loadings at girder ABC. Note that beams AD,BE and CF transmits its load to girders ABC and DEF. B. Determine the shear equation of girder ABC
A simply supported beam 300mm x 500mm has a span of 5m. The beam is reinforced with unbonded tendons. fse above the bottom of the beam f. = 35 MPa. Determine the following: 2. 750 MPа, Арs = 1200mm2 in tension zone located at 75 mm a. Reinforced indices for the beam b. Safe ultimate moment capacity c. Safe live load it could carry, weight of concrete is 24 kN/m³
3. A timber beam 250 mm x 300 mm is reinforced with steel plates 150 mm x 10 mm 9s rigidly attached at the top and bottom of the beam. Allowable stress of wood and steel are 8 MPa and 120 MPa respectively. Es = 300 000 MPa, Ew = 20 000 MPa. Determine the value of the following: a. The moment capacity of the beam without steel reinforcement. b. The moment capacity of the beam when reinforced with steel. c. The amount in which moment is increased by the reinforcement.
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
S1
4. The simply supported wood beam, fabricated by gluing together four wooden boards, caries the three concentrated forces. The working bending and shear stresses for the wood are 1000 psi and 600 psi, respectively. Determine the largest allowable value of the force P. 0.5 in. + 8 in. + 0.5 in. 2 in. P 2 ft -4 ft +4 ft- 2 ft 6 in. 12 in.
Find the forces acting in all members of the truss shown in Figure by using Method of joints and verify by Method of section.
60KN A ANALYZE THE STRUCTURE USING PORTAL FRAME METHOD Compute: 1. Axial Load of AD 2. Moment at Support B 3. Moment of Member EF at E Show Complete Solution B 7m E 5m LL F 8m
The floor system of a factory consists of a 5”-thick normal weight reinforcedconcrete slab resting on four steel floor beams (A = 14 in2) that, in turn, aresupported by two steel girders (A = 40 in2), as shown in the plan below.a. Should this slab be idealized as one-way spanning or two-way spanning?b. Draw the free-body diagram for the dead loads on beam BF and label themagnitude of all loads.c. Draw the free-body diagram for the dead loads on girder AD and label themagnitude of all loads.d. What is the axial load carried by column A?