The flexible area shown in Figure is uniformly loaded. Given that q = = 300kN/m² determine the vertical stress increase at point A.

Q: ) Write the equation for the neutral axis in the cross-section. b) Draw the normal stress…

A:

Q: For the figure shown, if the allowable stress is 80 MPa and the cross-sectional area is 1400 mm^2,…

A:

Q: The stresses shown act at a point in indicated in the figure. Using the ed plane shown. Assume ß =…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 95 MPa and Sy =…

A:

Q: indicated in the figure. Using the equilibrium equation approach, determine the normal and shear…

A: Given data in question  Stresses Angle To find out  Normal and shear stresses

Q: A bar of length 3 m is fixed at both the ends as shown in figure initial stress in bar is 30 MPa…

A:

Q: . For the plane stress situation shown in the figure, the maximum shear stress and the plane on…

A: A plane stress system as shown-Stress values-,To Find-The value of the maximum shear stress and the…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 60 MPa and Sy =…

A:

Q: The thin bar is subjected to an increase in temperature along its axis. Determine the end B of the…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and 5, =…

A: Given data in question  Stresses Angle To find out Normal and shear stress

Q: The cross-section of a shaft 90 mm diameter is subjected to a bending moment of 6 kNm and a twisting…

A:

Q: The stresses shown act at a point in a stressed body.  The stress magnitudes are Sx = 75 MPa and Sy…

A: Given data in question  Normal stresses Angle To find out  Normal and shear stresses

Q: W = 20000 N There is a gap between the aluminum bar and the rigid slab that is supported by two…

A: Solution:- By assuming no restrictions: We know that,              δT=αL∆T So, considering copper…

Q: Show the type of stress distribution over the radius of the disk 3. How is the correspondence…

A: The area of the middle section of the rod is reduced with respect to both ends which means the disk…

Q: In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit…

A: the largest P value according to the Von Mises assumption for the cube to be safe = 20a23explanation…

Q: A. In the figure below, the geology sign convention is used. Note: os is the shear stress 1. In…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 60 MPa and Sy =…

A:

Q: The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx =…

A: Given: The stress in the x-direction (Sx) is 170 MPa. The stress in the y-direction (Sy) is 85 MPa.…

Q: Problem 7.2-18 The surface of an airplane wing is subjected to plane stress with normal stresses o,…

A:

Q: The 2 D stress at a point is given by the matrix Txy 50 15 MPa. The maximum 15 10 6. II = Tyx yy…

A: To Find :The max shear stress ?

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx - 60 MPa and Sy=…

A:

Q: The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes ares, indicated in the…

A:

Q: Question 2: The plane strain values measured at the O point with the rosette in the figure are as…

A:

Q: a.) Determine the maximum normal stress developed in the bar when it is subjected to a tension of P…

A:

Q: a. Determine principal stress values b. Calculate the maximum inplane shear stress and average…

A:

Q: A 3-m long aluminum bar with a cross-sectional area of 320 mm2 is placed between two rigid walls as…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and S, =…

A: Given data in question  Normal stress on element  Angle  To find out  Normal and shear stresses

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and S, =…

A: Determine the normal and shear stresses at this point on the inclined plane shown.

Q: The state of stress at a point, for a body in plane stress, is shown in the figure below. If the…

A:

Q: The normal and shear stresses at a point in a structural subjected to a state of plane stress are…

A: To find principal stress and shear stress and their direction

Q: In a 2 dimensional stress analysis, the state of stress at a point is shown below in which length of…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy =…

A: Given Data:   Sx=60 Mpa Sy=-230 Mpa β=49°   It is asked to calculate Normal stress and shear…

Q: In order to determine the shear stress at A, using the shear stress formula, the thickness would be…

A:

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Given Data: Axial Load for Point H is P=3 kN. Shear Load for Point H in Y direction is VY=0.5 kN.…

Q: A cube of material (E 15,000 psi, v 0.25) of side length 2" is shown in the x, y plane. Take x…

A: Change in length of the cube depends on the length of the sides of the cube and the normal stress…

Q: The following stress element represents the stress state at point A of the structure in the figure…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.