Current Attempt in ProgressThe figure shows particles 1 and 2, each of mass m, attached to the ends of a rigid massless rod of length L₁ + L2, with L₁ = 2.0 m and L₂= 3.0 m. The rod is held horizontally on the fulcrum and then released. What are the magnitudes of the initial accelerations of (a)particle 1 and (b) particle 2?(a) Number(b) NumberUnitsUnits1L>>

The given configuration is is shown below as L1 = 2 m L2 = 3 m Moment of inertia (I) = m1L12 +…

The figure shows particles 1 and 2, each of mass m, attached to the ends of a rigid massless rod of length L₁ + L2, with L₁ = 2.0 m and L2 = 3.0 m. The rod is held horizontally on the fulcrum and then released. What are the magnitudes of the initial accelerations of (a) particle 1 and (b) particle 2? (a) Number (b) Number Units Units 14+ L 2 ✔

The figure shows particles 1 and 2, each of mass m, attached to the ends of a rigid massless rod of length L₁ + L2, with L₁ = 2.0 m and L2 = 3.0 m. The rod is held horizontally on the fulcrum and then released. What are the magnitudes of the initial accelerations of (a) particle 1 and (b) particle 2? (a) Number (b) Number Units Units 14+ L 2 ✔

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Chapter 11, Problem 066 GO Your answer is partially correct. Try again. In the figure, a small 0.109 kg block slides down a frictionless surface through height h = 1.46 m and then sticks to a uniform vertical rod of mass M = 0.218 kg and length d = 1.55 m. The rod pivots about point O through angle e before momentarily stopping. Find 0. Number Units (degrees) em the tolerance is +/-2% em Click if you would like to Show Work for this question: Open Show Work
A tetherball is connected to the top of a pole with a rope that is 2.58m long and swings around the pole at an angle of θ = 33.4 degrees between the pole and the rope. Calculate the speed of the tetherball in meters/second, but only enter in the numerical value, do NOT enter units.
The frame is made from uniform rod which has a mass p per unit length. A smooth recessed slot constrains the small rollers at A and B to travel horizontally. Force P is applied to the frame through a cable attached to an adjustable collar C. Determine the magnitudes and directions of the normal forces which act on the rollers if (a) h = 0.24L, (b) h = 0.50L, and (c) h = 0.91L. The forces will be positive if up, negative if down. Evaluate your results for p = 1.8 kg /m, L = 575 mm, and P = 48 N. What is the acceleration of the frame in each case? (a) Answers: (b) L (c) A h = 0.24L: h = 0.50L: h = 0.91L: L A = A A = B i i i P B N₁ B N, B N, i i N₁ª N,9 N₁9 i i m/s m/s m/s
Determine the magnitude of the linear acceleration of particle 1 (the left end) based on the following values, L1=20cm, L2=80cm the masses m are equal and the connecting rod has negligible mass. Enter units as m/s^2.
Determine the steady-state angle a if the constant force P = 155 N is applied to the cart of mass M = 32 kg. The cart travels on the slope of angle 0 = 24°. The pendulum bob has mass m = 7 kg and the rigid bar of length L = 1.2 m has negligible mass. Ignore all friction. P M m Answer: a = i
Please help me
A wheel of radius 0.269 m, which we can model as a thin disk, is mounted on a frictionless horizontal axis. The mass of the wheel is 2.44 kg. A massless cord wrapped around the wheel is attached to a block of 4.16 kg that slides on a horizontal frictionless surface. If a horizontal force P with a magnitude of 10.1 N is applied to the block as shown below. If the wheel and block start at rest, and the block is moved through a displacement of 2.60 m what is the final angular velocity of the wheel in rad/s, assuming the cord does not slip. P
Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension is 90 N in both portions of belt B and 150 N in both portions of belt C,determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust.
A 1.5-lb slider is propelled upward at A along the fixed curved bar which lies in a vertical plane. If the slider is observed to have a speed of 10.6 ft/sec as it passes position B, determine (a) the magnitude N of the force exerted by the fixed rod on the slider and (b) the rate v at which the speed of the slider is changing (positive if speeding up, negative if slowing down). Assume that friction is negligible. 29 2.8' Answers: N = Ib i ft/sec?
In the figure, a uniform sphere of mass m = 0.783 kg and radius r = 0.394 m is held in place by a massless rope attached to a frictionless wall a distance L = 1.58 m above the center of the sphere. Find (a) the tension in the rope and (b) the force on the sphere from the wall. L. (a) Number i Units (b) Number i Units
While installing new spark plugs in your car, the manual specifies they be tightened to 74 Nm. If you can only apply a force to the wrench 21 cm from the plug, and only at an angle of 53 degrees, What magnitude force should you apply to the wrench?