The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has diameter of 12 mm and the thickness of each steel plate is 15 mm. (a) Compute the shear stress (MPa) in each rivet due to a force of 10.2 kN applied to the plates. (b) If the bearing stress in the steel plates is limited to 40 MPa, what is the allowable load P (kN)? (c) If the width of the steel plates is 100 mm what is the allowable load P (kN) for a limited normal stress of 20 MPa? rivet cover plate Steel plate cover plate Elevation View Plan View

Q: Conduction An aluminum rod and an iron rod of equal length 2.0 m and cross-sectional area 2 cm? are…

A:

Q: A 37.5-mm-diameter rod 6 m long elongates 12 mm under a load 236 KN. The diameter of the rod…

A:

Q: Problem You are tasked with  analyzing the frame of a bubble fuselage. The frame is 3D printed…

A:

Q: d) i. Describe distributive forces. ii. Explain 3 (three) examples of distributive forces in terms…

A: Distributed forces: It is a force which acts on a surface, not just on one place.  The intensity of…

Q: the Torsion and, peoot Explain Formula Suitable of to ilth the help diagram ?

A: Torsion equation or torsion constant is defined as the geometrical property of a bar’s cross-section…

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: une at F = 5.5 kN (Figur

A: solution as follows

Q: Question (5): (a) The device shown in Fig. (5-a) is designed to apply pressure when bonding laminate…

A: Given Data At the handle 120N force is applied  Let us draw the reaction at the roller supports

Q: fimm. For the spring assemblage shown in the figure above, determine the displacement at node 2 and…

A: The value of spring constant is The displacement of node 3 is

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: With respect to flange-gasket-bolt/nut system following specifications are given. If the Gasket is…

A: Given: The outside diameter of shell, Ds = 90 cm The shell thickness, t = 8 mm = 0.8 cm The…

Q: 1. Create a free-body diagram for the above condition and apply the sign convention for forces and…

A: Mass of the man, mass of the box, angle in horizontal plane,the distance from the center of the…

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A:

Q: Give me right solution with clear calculations Question-3: - Initial error of the impact tester is…

A:

Q: What are the two basic failures/limit states of tension members and discuss? Derive the allowable…

A: Given question : What are the two basic failures/limit states of tension members and discuss? Derive…

Q: Compute the stress in the bar.

A: Here,  is strain developed in the bar. is compressed length. is initial length of the bar.. is…

Q: 3.8 The discs in the spinal column can withstand a stress (force per unit area) of 1.1 x 107 N/m2…

A: Given dataStress in the spinal column σmax = 1.1(10)7 N/m2Cros sectional area A = 10cm2= 10-3m2To…

Q: The rigid, horizontal slab is attached to two identical copper rods. There is a 1. gap a = 0.18 mm…

A:

Q: Mention with explanations three applications of Bernoulli's principle

A: What is Bernoulli's principle? This Bernoulli’s principle formulated by Scientist Daniel Bernoulli…

Q: 5. When unloaded, bars AB and AC are each 36 - in long and have a cross-sectional area of 2 in.…

A:

Q: FIGURE 3.16 Tension test on a round steel specimen showing grips and an exten- someter with an LVDT.

A: Given:

Q: (6) There are many kinds of polyethylene foam, each with different properties. The low density…

A: Given: The torque, T = 2 kN.m The elastic modulus, G = 6 GPa The diameter, d = 300 mm The length, L…

Q: Instructions: Write your solution and answer on a LBP/SBP/newsprint/yellow paper. Put your name and…

A:

Q: ---- at the end of the fire grate which is utilized in deflectin 7. In a Lancashire steam boiler,…

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: A socket of above knee amputee is used in the following analysis. It may considered as cylinder with…

A:

Q: What is the concept of ALARP? Give an example of a situation where the ALARP principle is applied.…

A: In this problem, we have to discuss the concept of ALARP with an example.

Q: Q) For the below figure (1), Find the magnitude of force required to rolling the cylinder over the…

A:

Q: 120 MPa in compression. (The working stress in compression is smalle to reduce the danger of…

A:

Q: A metallic rod of 500mm length and 50mm diameter, when subjected to a tensile force of 100 kN at the…

A:

Q: A uniform plank 9m long of mass 80 kg is horizontal. It is supported by vertical strings attached at…

A:

Q: 3. Specify number of statically determinate structure. 3) 2) M. M.

A:

Q: A: Draw the Free Body Diagram only of next fig. A TTTTT

A:

Q: Determine the horizontal force required to move a 2,539-lb automobile with 23-in.- diameter tires…

A: Here,   are the rolling resistance and radius of the wheel.

Q: Advanced hybrid materials technology has been used in automotive applications. A good example is…

A: Hybrid composite materials are employed in a variety of engineering applications due to their…

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A:

Q: and (b) by cylinder B? The for cylinder A and defe

A:

Q: (a) Estimate the number of cycles to failure. (b) If the bar is also placed in an environment with a…

A: