The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has diameter of 12 mm and the thickness of each steel plate is 15 mm. (a) Compute the shear stress (MPa) in each rivet due to a force of 10.2 kN applied to the plates. (b) If the bearing stress in the steel plates is limited to 40 MPa, what is the allowable load P (kN)? (c) If the width of the steel plates is 100 mm what is the allowable load P (kN) for a limited normal stress of 20 MPa?

Q: 3. Find Par as a function of · L2 for the given system. Use El = constant L L P

A: In this problem, the end conditions are to be finalised, and then crippling load for each member…

Q: Please solve it using a free body diagram. Show all the components. Don't use chatgpt,Only…

A: thank you

Q: Please draw the picture of this problem and solve it. A uniform rigid disk has mass M and radius…

A: To determine the force to pull rod and disc apart, given mass of the disc mass of the rod  radius of…

Q: Given the figure at the right, find the resultant of F1 and F2 (in vector form)

A:

Q: The mass of the block is mc=41 kg and the angle a=33deg. D. mc What is the tension in the cable D,…

A:

Q: The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is…

A:

Q: Problem 3 A gate is 1.5m in width and hinged at point A. Another point on the gate, B, is resting…

A:

Q: Looking for handwritten solution including Free body diagram.

A:

Q: Find the tensile force in rope AB. TAB = ? N Find the horizontal component of the reaction force at…

A:

Q: Please show the step-by-step solution. Please use pen and paper to solve. Thank you. Direction:…

A: Given: The structure is shown below:

Q: 30 B 45° 30° D

A: Part A) Draw the free body diagram at point B. Similarly, draw the FBD at Point D.

Q: Determine the reaction forces at points A, B & C. All supports have 2 forces. The first is…

A: The reaction forces at .FBD:The free-body diagram is shown below.

Q: s lowest point to the ground. Choices: 150m ,153m , 148m , 145

A: length = 300m   weight = 600kf   tension = 4ookg , 450kg

Q: Can you give me the free-body diagram?

A: Given data:- A pendulum of mass M1=1 kg  length L = 0.75 m . Mass of Block M2= 2 kg To find :- Free…

Q: The diagram to the left is a shelf connected to the wall by a fixed (cantilever) support. On the…

A:

Q: The cords ABC & BD can each support a maximum load of 274 lb. D. 1213 What is the maximum weight of…

A:

Q: Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that…

A:

Q: Find the spring constant if a 20. N force stretches a spring 2.0 m.

A: Given data : Force F=20 N Extension X=2 m   To find : Spring constant

Q: Q2: A: Draw the Free Body Diagram only of next fig.

A:

Q: The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is…

A:

Q: Problem 1: Replace the force system by a wrench. Also, find point P where the wrench intersects the…

A:

Q: Two concentric springs of equal lengths are placed in an assembly shown below. A force P is applied…

A: to select the correct options.

Q: The object that was horizontal before deformation, both shifted downward after the deformation and…

A: GIVEN:The object is horizontal initially before elongation. After elongation the angle made by the…

Q: also find ax and ay The rod is supported by smooth journal bearings at A, B. and Cand is subjected…

A:

Q: Find the spring constant if a 20. N force stretches a spring 2.0 m.

A: GivenF=20N∆=2m

Q: some reason, I get a different result despite I found all the right forces. Could you please tell me…

A:

Q: For the given system below, find the reactions exerted by the pin and the roller on the beam. Label…

A:

Q: A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the…

A: Given Length of the ladder = 10 m Weight of the ladder = 350 N Ladder angle = 30o Weight of the…

Q: Draw the Free Body Diagram only of next fig.

A:

Q: Problem 3. For the three forces shown in the figure below, find the resultant force, its magnitude,…

A:

Q: 5. In relation to question show free body diagram of the below figure

A:

Q: 52 Given F₁ 501b g=32.174 ft₂ Required: m=? Equation: F₁ = mg; m² mq; m-k = K g Solution: Answer m =…

A:

Q: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

A: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

Q: calculate reaction forces

A: Hand written solution is provided below.

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given,

Q: A: Draw the Free Body Diagram only of next fig. A TTTTT

A:

Q: Based on the figure, (a) The entire system is in equilibrium, both in translational and rotational…

A: (a) To explain:  What will happen to the tension in the string if Fapp moves further to the right .…

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. Z. 2 ft 4 ft 4 ft…

A:

Q: Locate the center of mass of the homogeneous bent wire in terms of (X,Y,Z). Show all steps. N 6 in.

A: To findLocate the center of mass of the homogeneous bent wire in terms of (x, y, z).Given

Q: i need this for now. please. someone who knows spanish, please help. Problem #2 2) 60 ఇం C D1- 61…

A:

Q: 2.5 m 5 m 7.5 m 5 m K 10 m 5 m K K K 20 m Obtain the center of stiffness

A: For solution refer below images.

Q: Three masses, m₁ = 2.5 kg, m₂ = 3 kg, and m3 = 1 kg, are attached to springs with stiffness…

A: The masses attached to the spring are-:The spring stiffness constant are-:

Q: 100 lb 50 Ib 45 250 lb 2. Determine M, P, and Q in the figure shown so that the resultant of the…

A:

Q: all relevant Free Body Diagrams.

A: Given