The figure below shows a Yo-Yo of mass m =245 g which has an axle of radius r=1.2 cm and a spool of radius R=5.2 cm. The Yo-Yo is placed upright on a horizontal plane. The string is pulled with a horizontal force Fas shown in the figure. What is the maximum magnitude of the pulling force, F. for which the Yo-Yo will roll without slipping? The coefficient of static friction between the Yp Yoand the horizontal plane is r06and the moment of inertia ofthe Yo-Yo about an axis passing thrOLigh its ceter is 1 = (i/2}mR

The figure below shows a Yo-Yo of mass m =245 g which has an axle of radius r=1.2 cm and a spool of radius R=5.2 cm. The Yo-Yo is placed upright on a horizontal plane. The string is pulled with a horizontal force Fas shown in the figure. What is the maximum magnitude of the pulling force, F. for which the Yo-Yo will roll without slipping? The coefficient of static friction between the Yp Yoand the horizontal plane is r06and the moment of inertia ofthe Yo-Yo about an axis passing thrOLigh its ceter is 1 = (i/2}mR

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure below, block 2 of mass m2 = 3.75 kg rests on a frictionless surface. It is attached to mass 1 (m1 = 2.50 kg) by a massless, stretchless string that passes over a frictionless pulley of radius R = 15.0 cm. When released from rest, block 2 moves to the right with an acceleration of 3.80 m/s2. What is the mass of the pulley? must draw FBDs
A thin cord is wrapped around a uniform grindstone of radius 0.30 m and mass of 25 kg supported by bearings that produce negligible friction torque. The cord exerts a steady tension force on the grindstone, causing it to accelerate from rest to 60 rad/s in 12 s. (lgrindstone = 5 What is the magnitude of the tension force of the cord? O 5.6 N 11.3 N O 18.7 N O 37.5 N
At what maximum speed can a car manage a turn on a wet, level road with coefficient of static friction 0.230 without sliding out of control? The radius of the turn is 25.0 m
Consider the setup shown below. The blocks have masses 3.6 kg and 24 kg. The pulley has mass 7.4 kg, and is a uniform disc with radius 0.23 m. Assume the pulley to be fric- tionless, but the coefficient of friction between the block and the surface is 0.36. a T2 3.6 kg T1 = 0.36 22° 24 kg What is the acceleration of the blocks? As- sume the 24 kg mass is descending with accel- erațion a. The moment of inertia of the disk is - M R? and the acceleration of gravity is 2 9.8 m/s?. Answer in units of m/s?.
A block of mass 2 kg slides down an inclined plane at an angle of 45° with a massless tether attached to a pulley with mass 3 kg and radius 0.7 m at the top of the incline (see the following figure). The pulley can be approximated as a disk. The coefficient of kinetic friction on the plane is 0.2. What is the acceleration of the block (in m/s²)? (Enter the magnitude.) 3.59 45° x m/s²
Find the net torque on the wheel in the figure below about the axle through O, taking a = 13.0 cm and b = 31.0 cm. (Assume that the positive direction is counterclockwise.) N·m 12.0 N 30.0% 10.0 N 9.00 N
A coke can is suspended by a string from the tab so that it spins with a vertical axis. A 14 N perpendicular force at the edge causes rotation. Find the angular acceleration if the can has a radius of 4 cm and a mass of 427 grams.
In the figure, what magnitude of force F applied horizontally at the axle of the wheel is necessary to raise the wheel over an obstacle of height h = 0.356 m? The wheel's radius is r = 0.662 m and its mass is m = 1.71 kg. F
M, R m1 m2 Refer to the figure above for this problem. A wooden bldck of mass m, = 3.2 kg and a hollow block of mass m2 = 8.7 kg are connected by a rope which runs over a friction-less pulley. Assume that the pulley is a solid iron disc with a radius R = 0.3 m and mass M = 5.1 kg. The ramp is wedge- shaped and makes an angle of 0=36°. The coefficient of kinetic friction is 0.29 for both blocks and the wedgeshaped incline. (a) Draw force diagrams of both blocks and of the pulley. (b) Determine the acceleration of the two blocks. (c) Determine the tensions in the string on both sides of the pulley.
As a torque activity, your Physics TA sets up the arrangement shown below. 3 F_= A uniform rod of mass m = 118 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r₁ = 10.0 cm and r₂ = 90.0 cm mark, passed over pulleys, and masses of m₁ = 271 g and m₂ = 137 g are attached. Your TA asks you to determine the following. (a) The position r3 on the rod where you would suspend a mass m3 = 200 g in order to balance the rod and keep it horizontal if released from a horizontal position. In addition, for this case, what force (magnitude and direction) does the pin exert on the rod? Use standard angle notation to determine the direction of the force the pin exerts on the rod. Express the direction of the force the pin exerts on the rod as the angle F, measured with respect to the positive x-axis (counterclockwise is positive and clockwise is negative). m4 F_= OF = "5 (b) Let's now remove the mass m3 and determine the new mass m4 you would…
Item 9 A garage door is mounted on an overhead rail (Figure 1). The wheels at A and B have rusted so that they do not roll, but rather slide along the track. The coefficient of kinetic friction is 0.54. The distance between the wheels is 2.00 m, and each is 0.50 m from the vertical sides of the door. The door is uniform and weighs 900 N. It is pushed to the left at constant speed by a horizontal force F, that is applied as shown in the figure. Figure B k A K 2.00 m -3.00 m h F 1 of 1 If the distance his 1.60 m, what is the vertical component of the force exerted on the wheel A by the track? Express your answer to two significant figures and include the appropriate units. μA ? nA = Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part B If the distance h is 1.60 m, what is the vertical component of the force exerted on the wheel B by the track? Express your answer with the appropriate units. μÅ ? nB = Value Units Submit Request Answer Part…
The figure below shows a human arm that weighs 41.10 N. The arm is extended outward and is motionless. The gravitational force Fg on the arm acts at point A, a distance of 0.2900 m from the shoulder joint, which is represented by point O. The shoulder pushes down and to the right on the humerus bone of the arm with a force Fs at point O, at an angle ? as shown. The deltoid muscle pulls back on the arm toward the shoulder with a tension force Ft. This tension force acts at a point 0.08000 m to the right of point O, and it is directed up and to the left, at a 12.00° angle with respect to the horizontal. An arm is extending horizontally to the right with a cutout that shows muscles in the upper arm. A horizontal dashed line extends along the bottom of the muscles and another along the top. Point O is labeled at the left end of the arm on the lower horizontal line. An unlabeled point lies 0.080 m horizontally to the right of point O. Point A lies 0.290 m horizontally to the right of point…