the external and internal diameters of hollow cylinder are 115mm and 99mm respectively. when the cylinder is compressed by an axial force of 180kn the outer

Q: The sectional dimension of a reinforced concrete short column is b X h= 400 mm X 400 mm. The length…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: The tank shown in the figure is fabricated from a 10 mm steel plate. Determine the longitudinal and…

A:

Q: A rubber ball is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240…

A:

Q: The reinforced concrete beam shown is subjected to a positive bend-ing moment of 175 kN·m. Knowing…

A: Following is the given figure: Compute the modular ratio as follows: Substituting the values…

Q: A pressure-vessel is fabricated by gluing the circular plate to the end of the vessel as shown in…

A: Internal pressure = P = .45MPa Diameter = d = 450mm Thickness = t = 10mm Side thickness = t' = 20mm

Q: The internal diameter of a thin cylinder is 200 mm and it is subjected to internal pressure of 15…

A:

Q: WATE IS PLACED IN A HYDRAULIC PRESS INITIALLY OF 140 kPa ABSOLUTE, THE PRESSURE IS NCREASED TO…

A: Given data- Initial Pressure = 140 kPa Final Pressure = 222538 kPa Bulk Modulus (K) = 2.5 GPa To…

Q: m2. Calculate the tangential stress in the steel in MPa.

A: PRESSURE VESSELS:

Q: Q.2. A \\ Iron-carbon alloys tested by compression test,where L - 30 mm, and Lf - 33.7 min.,…

A: Part A Strain = 33.7-30/30= 0.123 Part b 1  Elastic modulus* Strain 2. Compression test

Q: A circular tube of outer diameter D is slipped over a 40-mm-diameter solid cylinder. The tube and…

A:

Q: 5. Determine if the flexural stress of the chocolate will increase or decrease if changes are made…

A:

Q: A hollow bronze cylinder is compressed by a P force. It has an internal diameter d1 = 1.85 in and an…

A:

Q: The plastic modulus of a section is 5 x 10-4 m³. Its shape factor is 1.2 and the plastic moment…

A: Given data- Plastic modulus- Zp=5×10-4 m3, Shape factor SF=1.2, Plastic moment capacity- Mp=120…

Q: For the punching operation shown in the figure, compute the shear stress in the material if a force…

A:

Q: I need the answer as soon as possible

A: Given data:- Cross-section of plate is 0.5 m × 0.3 m  Thickness of plate is 0.01 m Young's Modulus…

Q: show solution of: A liquid compressed in a container has a volume of 1 liter at a pressure of 1 MPa…

A:

Q: A flat bar of cross section 15 mm by 70 mm elongates 2.59 mm in a length of 1.3 m as the result of…

A: Axial stress is the ratio of load and the areaσ=PAσ=230,000N15×70 mm2σ=219Mpa

Q: a concrete beam simply supported at both ends 300 × 600mm it stressed by 3 cables of 700 mm each…

A: given data: ps =1200n/mm2                     e=100mm, ec =30,000

Q: civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3…

A:

Q: A thin cylindrical pressuhe pipe with both ends closed has diameter 1000 mm, The pipe Es subjected…

A:

Q: A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's…

A:

Q: 1) The plastic polymer cylindrical pipe is carrying flowing water at 0.5 N/mm pressure. The pipe has…

A:

Q: The rigid horizontal slab is attached to two identical copper rods. There is a gap Δ = 6.18 mm…

A: Finding change in length and stress induced due to temperature rise

Q: In a compression test and for a very ductile material similar to copper , the diameter and the…

A: Initial length Lo = 80 mm Initial diameter Do = 60 mm Final diameter D = 120 mm Final length = ?

Q: 400 11.7 200 x 10° ronze teel - m-

A: To find the stress in each bar-

Q: A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner…

A: Given: Length of rod, L = 1 m = 1000 mm Outside diameter of rod, Do = 0.2 m = 200 mm Inner diameter…

Q: A hollow circular shaft of inner radius 10 mm, outer radius 20 mm and length 1 m is to be used as a…

A:

Q: Determine change in volume of the block.

A: Given data, Steel block is subjected to a, hydrostatic pressure is=10 MPaYoung's modulus=150…

Q: A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's…

A: Given data,  Volume of steel block = (100×40×20)mm³   =  80000mm³                      Hydrostatic…

Q: Axial deformation in a bar loaded in the axial direction can be reduced by which of the following?…

A: Given data  Axial deformation in bar can be reduce by which of the following way when axial load is…

Q: A solid circular steel column is 3 m long and 0.4 m in diameter. It carries a load of 50 MN. The…

A: Given that , length = 3 m diameter = 0.4 m load P = 50 MN = 50 × 106 N E = 200 Gpa = 20 × 109 pa =…

Pressure and Stress