The equation for FM wave is s(t) = 11 cos [653451272t + 67 cos 10085t] Find the following: (1) carrier frequency fc [ (i) modulating frequency fm (iii) modulation index mf ! (iv) frequency deviation Af [ (v) deviation sensitivity if the maximum amplitude of the message is 9V4 (vi) power dissipated in 1442 resistor (vii) Bandwidth of the FM Wave

The equation for FM wave is s(t) = 11 cos [653451272t + 67 cos 10085t] Find the following: (1) carrier frequency fc [ (i) modulating frequency fm (iii) modulation index mf ! (iv) frequency deviation Af [ (v) deviation sensitivity if the maximum amplitude of the message is 9V4 (vi) power dissipated in 1442 resistor (vii) Bandwidth of the FM Wave

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discussion: 1. Sketch the waveform for the message and phase modulation. 2. What is the difference between phase modulation and frequency modulation? 3. The phase modulation is shown below: XpM = 5Cos(2 + n10St + 0.05cos2n10*) i. find equation of the message if Kp=5 ii. Find Total power for PM modulation
Discussion: 1. Sketch the waveform for the message and phase modulation. 2. What is the difference between phase modulation and frequency modulation? 3. The phase modulation is shown below: XpM = 5Cos(2 n10 t + 0.05cos2m10*) i. find equation of the message if Kp=5 ii. Find Total power for PM modulation
Consider the following continous time signal x(t). Assume that the signal was sampled at a sampling frequency of 20 Hz. Plot the magnitude spectrum of the sampled signal as a function of cyclic frequency. Be sure to include n values of up to +-2. Label x and y axis. Did aliasing occur? If so, what is the aliased frequency? x(t) = 1 + 2cos(2pi25t)
Type your question here The input resistance of acertain wideband oscilloscope is selectable at either 50Ω or 1?Ω. The noise bandwidth is 500 ??? and the equivalent noise temperature is 600 ??. If the average input signal power must be at least ten times the average noise power for measurement accuracy. What is the minimum acceptable rms input signal at each resistance level under open circuit conditions r no additional noise? (Assume that the input resistance is a thermal noise source)
Calculate the maximum frequency deviation for the FM signal v(t) = 10 cos (6000t+ 5sin2200t) a. 2200 Hz b. 6000 Hz c. 1750 Hz d. 11000 Hz
1) From the plots, what is the frequency of the input signal (in samples as well as radians)? 2) From the plots, what is the frequency of the output signal (in samples and radians)? 3) What does echo do to the magnitude and phase spectra?
I need the answer as soon as possible
A receiver is being tested to determine SIINAD. A 400-Hz audio signal modulates a carrier that is applied to the receiver. Under these conditions, the output power is 7 mW. Next a filter is used to cancel the 400-Hz portion of the output, and then an output power of 0.18 mW is measured. Calculate SINAD. Cevap: Sonraki sayfa ar Geçiş yap.. on sy...pdf W
R R OVOUT 2R 2R 2R 2R 2R VREF O If Vref=5V, for this setting of R2R DAC switches, what is the output voltage?
2. (b) A periodic composite signal is composed of 2 sine waves(S1,S2). The frequency (f) and maximum amplitude (A) of each sign wave is given below: S1:f = 5KHZ , A = 6V S2 :f = 8Khz , A = 4V Draw a frequency domain graph to represent this information. What is the bandwidth?
The modulating signal directly deviates the carrier's frequency in this angle modulation. Select your answer. Direct FM Indirect FM Indirect PM Direct PM
Calculate the maximum frequency deviation for the FM signal v(t) = 10 cos (6000t+ 5sin2200t) a. 2200 Hz b. 6000 Hz c. 1750 Hz d. 11000 Hz