The engineer needs to design a cylinder shaft, with length L=1 m, to transmit a power of 500W and rotating at 17 rad/s. The radius of the cross-section is 0.01m, which gives us the polar 2nd moment of area J=1.57x10 m². Two materials can be chosen: Material A: expensive, shear modulus G-80GPa, and the maximum allowed shear stress is 280MPa Material B: cheap, shear modulus G=25GPa, and the maximum allowed shear stress is 200MPa (a) Determine the torsion angles if material A or B is applied, respectively. (b) If the safety MUST be ensured, and a lower cost is preferred, which material should be chosen? (Safety factor = 0.8)

The engineer needs to design a cylinder shaft, with length L=1 m, to transmit a power of 500W and rotating at 17 rad/s. The radius of the cross-section is 0.01m, which gives us the polar 2nd moment of area J=1.57x10 m². Two materials can be chosen: Material A: expensive, shear modulus G-80GPa, and the maximum allowed shear stress is 280MPa Material B: cheap, shear modulus G=25GPa, and the maximum allowed shear stress is 200MPa (a) Determine the torsion angles if material A or B is applied, respectively. (b) If the safety MUST be ensured, and a lower cost is preferred, which material should be chosen? (Safety factor = 0.8)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem: 1 A line shaft rotating at 55 RPS is to transmit 28 kW. The shaft may be assumed to be made of mild steel with an allowable shear stress of 85 MPa. Determine the diameter of the shaft, neglecting the bending moment on the shaft.
A section of a wing torque box, 40 ft long w/ shear modulus G = 12 x 10^6 psi carries the torque 120 kip.in., has configuration of a semi-circular section w/ radius of 5 in & center at O. (a) Compute the constant thickness t if the shear stress is limited to 12 ksi. (b) Find the constant wall thickness t if the angle of twist is not to exceed 2°. (c) Determine the smallest allowable constant wall thickness t to satisfy both conditions. (Select the three corresponding correct answers) * 0.573 in 0.064 in 0.350 in tmin = 0.350 in tmin = 0.573 in tmin = 0.130 in 0.130 in tmin = 0.064 in
Problem 2. A 300-mm diameter solid disk is to be used as a flywheel in a machine to reduce speed fluctuations. If the disk material has yield strength S Y =720 MPa, density p=7000 kg/m^ 3 . and Poisson's ratio J = 0.2 ^ c , find the maximum allowable rotational speed (in rpm) for a safety factor of 1. a) Solve using the MSST. b) Solve assuming that the disk is mad of cast iron having Sut = 207MPa , Fuc = 780MPa, p = 7000 kg/m³, and Poisson's ratio v r = 0.26 , Use Coulomb-Mohr theory.
A solid circular drive shaft of length = 0.5 m, is to be designed to transmit up to 45000 W at 1800 rev/min. If the maximum allowable shear stress is 60 MN/m? and the modulus of rigidity, G = 79 GPa, determine the following: Q4 b) The minimum diameter of the shaft
Q4. Determine the diameter of a shaft which is transmitting 60KW at 200rev/min, for: 1- Solid shaft 2- Hollow shaft with a diameter ratio of 0.6 If the maximum shear stress in shaft is 70MN/m' and angle of twist to 3.8" in length of 4m. Take for the shaft material C=80GN/m'.
HOMEWORK: Q1/ A beam carries the loads shown in figure, if the tensile stress must not exceed 20 MPa and the compression stress 70MPA. Find the maximum value of load P 50mm はomm W=2.5p Kw/m 300 Im tan 4m lom ww 150mm Q2/ A beam has a cross section as shown below with unknown dimensions of the flange (b,) and the web (b,) and is subject to a maximum positive moment at the center which causes a tensile stresses at points A and B of 900N/cm2 and 600 N/cm? respectively ba 10 J00KN 50 Cm sm 200cm
3. Two cylindrical hollow shafts with shear modulus G = 77 GPa are welded together to a rigid connecting plate. A torque at C causes the connecting plate to rotate 8. Find the maximum shear stress in each shaft. Diameter A C = 30 cm Diameter CB = 20cm 0.5cm 1 cm
Please no plagiarsm and copy the answer from the chegg thanks A rectangular wooden beam (fb = 5.9 MPa, E = 17.3 GPa) has a cross-sectionalarea of 250 mmby 500 mm. The length of the beam is 15 meters with pin and roller supports every fifth points. A vibratingmachine weighing 500 kg is located at the mid-lengthof the beam. The machine produces anunbalanced force of 500 N operating at 300 rpm.Determine the following: a) maximum static deformation under the weight of the machine,b) maximum dynamic stress in the beam section under the unbalanced force,c) force transmitted to the support, andd) adequacy of the beam against bending. Use a dampingratio of 5%.
A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is transmitted via the drive shaft, ABC. The section AB is a solid circular shaft 0.7 m long and the section BC is a hollow circular shaft 1.0 m long with 110 mm outer diameter and 55 mm inner diameter. Both shafts are made from a metal alloy (Shear Modulus G = 95 GPa). 0.7 m 1.0 m A в 2400 hp @ 2000 rpm Figure 3 a) If the drive shaft rotates at 2000 rpm and the power transmitted along the shaft is 2400 hp (1 hp = 745.7 W), calculate the torque developed in the drive shaft.
Elasticity and Stress Analysis: Torsion The three cell box girder of Figure 1 Q.1 is subjected to a clockwise torque of 10,000 kNm.Sketch the shear flow diagram for the girder.Hence, determine the shear stress set up in each member and the angle of twist of thegirder.Given: Modulus of Rigidity = 80 GN/m2 Equations: T=2Ah 2G(theta)A=(tau)L q1=q2+q3
The Cantilever beam in Fig. 5, has a circular cross section (diameter-100 mm) (a)find the shear stress in the beam in points (a,b.c.d and e) due to applied the uniform load 3 kN/m and the torque 4kN.m. (2) Sketch the shear stress distribution over the cross section. Dia 100 mm B. 3 kN/m 4 kN.m C. 4 m 1 m Fig
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.