The engine generates electrical power at 1MW. At 500°C a temperature of 1.5MW heat is sent from the heater to the high temperature boiler. The engine also absorbs 0.5MW as heat from burning fuel at a temperature of 300 °C. Engine cooling occurs in the environment at a temperature of 25°C a. Calculate the amount of heat that needs to be removed from the system at 25°C (cooling requirements) b. Can this machine operate as planned? Prove your answer with the concept of entropy

The engine generates electrical power at 1MW. At 500°C a temperature of 1.5MW heat is sent from the heater to the high temperature boiler. The engine also absorbs 0.5MW as heat from burning fuel at a temperature of 300 °C. Engine cooling occurs in the environment at a temperature of 25°C a. Calculate the amount of heat that needs to be removed from the system at 25°C (cooling requirements) b. Can this machine operate as planned? Prove your answer with the concept of entropy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A refrigerant system with a capacity of 15 tons of refrigeration operates at 150 KPA evaporator…

Q: ! Required information A steady-flow Carnot refrigeration cycle uses refrigerant-134a as the working…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: A Carnot refrigeration cycle uses refrigerant-134a as the working fluid. The refrigerant evaporates…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: 2. A refrigeration system with a capacity of 10 tons of refrigeration, operates at 210 kPa in the…

Q: A commercial refrigerator with refrigerant-134a as the working fluid is used to keep the…

Q: A refrigerant 12 refrigeration system requires a load of 54 kW at an evaporator pressure of 270 kPa…

Q: A refrigerator uses refrigerant-134a as the working fluid and follows the ideal vapor-compression…

Q: Problem 2 A window air conditioner consumes 0.8 kW of electricity during steady-state operation. If…

Q: standard vapor compression cycle using R134a as the working fluid has a condensing temperature of…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: A commercial refrigerator with refrigerant-134a as the working fluid is used to keep the…

A: Given:Refrigerant=R134aSpace temperature, T=-30oCWater inlet temperature, Tw,i=18oCWater mass flow…

Question

The engine generates electrical power at 1MW. At 500°C a temperature of 1.5MW heat is sent from
the heater to the high temperature boiler. The engine also absorbs 0.5MW as heat from burning fuel
at a temperature of 300 °C. Engine cooling occurs in the environment at a temperature of 25°C
a. Calculate the amount of heat that needs to be removed from the system at 25°C (cooling
requirements)
b. Can this machine operate as planned? Prove your answer with the concept of entropy

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The figure below shows a two-stage vapor-compression refrigeration system with ammonia as the working fluid. The system uses a direct-contact heat exchanger to achieve intercooling. The evaporator has a refrigerating capacity of 40 tons and produces -30°F saturated vapor at its exit. In the first compressor stage, the refrigerant is compressed adiabatically to 140 lbf/in.², which is the pressure in the direct contact heat exchanger. Saturated vapor at 140 lbf/in.² enters the second compressor stage and is compressed adiabatically to 250 lbf/in.² Each compressor stage has an isentropic efficiency of 85%. There are no significant pressure drops as the refrigerant passes through the heat exchangers. Saturated liquid enters each expansion valve. Determine: Expansion valve 6- Condenser Direct contact heat exchanger Expansion valve (a) the ratio of mass flow rates, m3/my. (b) the power input to each compressor stage, in horsepower. (c) the coefficient of performance Comp Comp Evaporator
A manufacturer claims that the average tensile strength of thread A exceeds the average tensile strength of thread B by at least 12 kilograms. To test this claim, 50 pieces of each type of thread were tested under similar conditions. Type A thread had an average tensile strength of 86.7 kilograms with a standard deviation of 6.28 kilograms, while type B thread had an average tensile strength of 77.8 kilograms with a standard deviation of 5.61 kilograms. Test the manufacturer’s claim using a 0.05 level of significance. 1. Determine the Z calculated in two decimal places. 2. Determine the Z table in two decimal places. 3. Is the manufacturing claim statistically valid? yes or no
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a two-stage cascade refrigeration cycle with a flash chamber as shown in the figure with refrigerant-134a as the working fluid. The evaporator temperature is −10°C and the condenser pressure is 1600 kPa. The refrigerant leaves the condenser as a saturated liquid and is throttled to a flash chamber operating at 0.45 MPa. Part of the refrigerant evaporates during this flashing process, and this vapor is mixed with the refrigerant leaving the low-pressure compressor. The mixture is then compressed to the condenser pressure by the high-pressure compressor. The liquid in the flash chamber is throttled to the evaporator pressure and cools the refrigerated space as it vaporizes in the evaporator. The mass flow rate of the refrigerant through the low-pressure compressor is 0.11 kg/s. Assume that the refrigerant leaves the evaporator as a saturated vapor…
your client needs to know about the mass flow rate ofsteam needed for a 1500 kW plant. The heat supplied to the steamin the boiler is 2700 k//kg, the heat rejected by the steam to thecooling water in the condenser is 2000 kJ/kg, and the feed pumpwork required to pump the condensate back into the boiler is 3.5 kWCalculate the mass flow of steam required
Please solve
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A commercial refrigerator with refrigerant-134a as the working fluid is used to keep the refrigerated space at -30°C by rejecting its waste heat to cooling water that enters the condenser at 18°C at a rate of 0.29 kg/s and leaves at 26°C. The refrigerant enters the condenser at 1.2 MPa and 65°C and leaves at 42°C. The inlet state of the compressor is 60 kPa and -34°C and the compressor is estimated to gain a net heat of 430 W from the surroundings. The heat exchanger loses no heat to the environment. 26°C 42°C ↓ Condenser 3 Expansion valve Water 18°C Evaporator QL (2) 1.2 MPa 65°C lin Win Compressor 60 kPa -34°C Determine the COP of the refrigerator. (You must provide an answer before moving on to the next part.) The COP of the refrigerator is