IThe endpoint of an acid-base titration is defined as the point whereO A. The amount (moles) of acid and base present are equivalent and a physio-chemical change occurs.O B. All the base added from the burette is used up.O C. Excess titrant is present.O D. The number of moles of acid and base are equal.

" The endpoint of an acid-base titration is defined as the point where. O A. The amount (moles) of acid and base present are equivalent and a physio-chemical change occurs. B. All the base added from the burette is used up. C. Excess titrant is present. O D. The number of moles of acid and base are equal.

" The endpoint of an acid-base titration is defined as the point where. O A. The amount (moles) of acid and base present are equivalent and a physio-chemical change occurs. B. All the base added from the burette is used up. C. Excess titrant is present. O D. The number of moles of acid and base are equal.

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter16: Reactions Between Acids And Bases

Section: Chapter Questions

Problem 16.90QE

See similar textbooks

Similar questions

Another way to treat data from a pH titration is to graph the absolute value of the change in pH per change in milliliters added versus milliliters added (pH/mL versus mL added). Make this graph using your results from Exercise 61. What advantage might this method have over the traditional method for treating titration data?
An acid is titrated with NaOH. The following beakers are illustrations of the contents of the beaker at various times during the titration. These are presented out of order. Note: Counter-ions and water molecules have been omitted from the illustrations for clarity. (a) (b) (c) (d) (e) a. Is the acid a weak or strong acid? How can you tell? b. Arrange the beakers in order of what the contents would look like as the titration progresses. c. For which beaker would pH = pKa? Explain your answer. d. Which beaker represents the equivalence point of the titration? Explain your answer. e. For which beaker would the Ka value for the acid not be necessary to determine the pH? Explain your answer.
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
Describe how the amount of sodium hydroxide in a mixture can be determined by titration with hydrochloric acid of known molarity.
Follow the directions of Question 64. Consider two beakers: Beaker A has a weak acid(K a=1105). Beaker B has HCI. The volume and molarity of each acid in the beakers are the same. Both acids are to be titrated with a 0.1 M solution of NaOH. (a) Before titration starts (at zero time), the pH of the solution in Beaker A is the pH of the solution in Beaker B. (b) At half-neutralization (halfway to the equivalence point), the pH of the solution in Beaker A the pH of the solution in Beaker B. (c) When each solution has reached its equivalence point, the pH of the solution in Beaker A the pH of the solution in Beaker B. (d) At the equivalence point, the volume of NaOH used to titrate HCI in Beaker B the volume of NaOH used to titrate the weak acid in Beaker A.
For a titration to be effective, the reaction must be rapid and the yield of the reaction must essentially be 100%. Kc1,1, or 1 for a titration reaction?
You have a solution of the weak acid HA and add some HCl to it. What are the major species in the solution? What do you need to know to calculate the pH of the solution, and how would you use this information? How does the pH of the solution of just the HA compare with that of the final mixture? Explain.
Consider the following two acids: In two separate experiments the pH was measured during the titration of 5.00 mmol of each acid with 0.200 M NaOH. Each experiment showed only one stoichiometric point when the data were plotted. In one experiment the stoichiometric point was at 25.00 mL added NaOH, and in the other experiment the stoichiometric point was at 50.00 mL NaOH. Explain these results. (See Exercise 113.)
Explain why the hydrolysis of salts makes it necessary to have available in a laboratory more than one acid-base indicator for use in titrations.
A bottle of concentrated hydroiodic acid is 57% HI by weight and has a density of 1.70 g/mL. A solution of this strong and corrosive acid is made by adding exactly 10.0 mL to some water and diluting to 250.0 mL. If the information on the label is correct, what volume of 0.988 M NaOH is needed to neutralize the HI solution? Suggest an indicator for the titration.
60.0 mL of 0.625 M HNO, is titrated by 0.200 M KOH. Calculate the pH of the acid solution before any titrant is added. pH = Calculate the pH after 141.8 mL of 0.200 M KOH is added to 60.0 mL of 0.625 M HNO3. pH= Calculate the pH after 187.5 mL of 0.200 M KOH is added to 60.0 mL of 0.625 M HNO pH= Calculate the pH after 318 mL of 0.200 M KOH is added to 60.0 mL of 0.625 M HNO3. pH=
Part (c) and (d) only