w8 The effective impedances of the main and auxiliary windings of a capacitor-start inductionmotor under locked-rotor conditions are given as follows:Main winding: effective resistance = 5.3 2; effective reactance = 9.6 2Auxiliary winding: effective resistance = 7.5 2; effective reactance = 3.2 2If the VL is 150 V,a. Illustrate the equivalent circuit and determine the magnitude of real, reactive andapparent powers from the main and auxiliary windings.b. Calculate the phase angle between Ia and Is.c. Calculate the line current IL.d. Determine the power factor under locked-rotor conditions.

In this question, We need to determine the power across each winding We know apperent power S= VI*…

The effective impedances of the main and auxiliary windings of a capacitor-start induction motor under locked-rotor conditions are given as follows: Main winding: effective resistance = 5.3 Q; effective reactance = 9.6 Q Auxiliary winding: effective resistance = 7.5 Q; effective reactance = 3.2 N If the VL is 150 V, a. Illustrate the equivalent circuit and determine the magnitude of real, reactive and apparent powers from the main and auxiliary windings. b. Calculate the phase angle between la and Is. c. Calculate the line current IL. d. Determine the power factor under locked-rotor conditions.

The effective impedances of the main and auxiliary windings of a capacitor-start induction motor under locked-rotor conditions are given as follows: Main winding: effective resistance = 5.3 Q; effective reactance = 9.6 Q Auxiliary winding: effective resistance = 7.5 Q; effective reactance = 3.2 N If the VL is 150 V, a. Illustrate the equivalent circuit and determine the magnitude of real, reactive and apparent powers from the main and auxiliary windings. b. Calculate the phase angle between la and Is. c. Calculate the line current IL. d. Determine the power factor under locked-rotor conditions.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5
What is the per unit impedance of a 50 MVA, 2% impedancetransformer if the base is changed to 100 MVA?
Where does Wye-Delta circuit used in industry application? What specific application and explain
7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the load current. Wiso 150 75 28 100
e) Find the total reactive power in the sound system without using the voltages across loads.Mention the unit. f) Find the apparent power of the system. Mention the unit.
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
Group Work (a) Determine the total resistance in the circuit below. (b) Determine the current in the circuit below. (c) What is the power dissipated by the entire circuit? (d) What is the power dissipated by R₁? 12.0 V I = ? V₁ = ? 1.00 Ω m R₁ R₂₂ 6.00 £2 1₂ = ? F3 3- 13 13.0 22 Vp= V - V₁ = ?
A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 63.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.6122 c. 0.6511 d. 0.4472
For the bridge circuits shown in the figure bellow, derive expressions to calculate the unknown impedances. Be Detector wwlle
https://www.bartleby.com/questions-and-answers/electrical-engineering-question/9c943287-9a69-4fab-befd-4a1bf010de19
The formula to calculate the load regulation is
Q4/ What is the three phase emf generation and show their two main advantages with type of connection in three phase circuit.