The distribution constant for iodine between an organic solvent and water is 75. Find the concentration of I2 remaining in the aqueous layer after extraction of 100 mL of 1.50 x 10^-3 M I2 with the following quantities of the organic solvent: (a) 100 mL; (b) three 50 mL; (c) four 20 mL portions Note: Write the answer in (a), (b) then in (c) separated Use 2 decimal places only.

The distribution constant for iodine between an organic solvent and water is 75. Find the concentration of I2 remaining in the aqueous layer after extraction of 100 mL of 1.50 x 10^-3 M I2 with the following quantities of the organic solvent: (a) 100 mL; (b) three 50 mL; (c) four 20 mL portions Note: Write the answer in (a), (b) then in (c) separated Use 2 decimal places only.

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter3: Statistical Tests With Excel

Section: Chapter Questions

Problem 6P

See similar textbooks

Similar questions

A reagent bottle contains 250 cm3 of 0,4 mol.dm–3 oxalic acid(C2O4H2) solution. Calculate the mass of pure oxalic acid thatmust be dissolved in this solution so that its new concentration is 0,6 mol.dm–3. Assume that the volume of the solution remainsconstant
16) Which of the following(s) is/are correct? I- Selectivity factor is the amount of time a solute spends in the stationary phase relative to the time it spends in mobile phase II- The retention time for an analyte is the time interval between its injection onto a column and its appearance at the detector at the other end of the column. III- Distribution constant is the ratio of the total solute concentration in the stationary phase to that in the mobile phase. A) I, II and III B) Only II C) I and III D) II and III E) Only III for GC2
How to make a 250 mL stock of 500 mM Tris-HCl, pH 8 and a 100 mL stock of 250 mM EDTA. Then, state how much of each of these stock solutions you would use to make a 50 mL solution of TE (also include how much distilled water would be used). I tried looking up other solutions with different quanities so i can try to do it myself but couldnt find anything anywhere.
You have been asked to make a guess as to the type of alkalinity present for the water samples listed below (hydroxide, carbonate, and/or bicarbonate) in each of the samples: (Use all the assumptions that we used in lab) Species present total ml to titrate all of the alkalinity due to the carbonate in the original solution A: Vp = 0 ml; Vmo = 0 ml B: Vp = 10 ml; Vmo = 10 ml C: Vp = 15 ml; Vmo = 5 ml D: Vp = 5 ml, Vmo = 10 ml
The distribution constant for X between n-hexane and water is 8.9. Calculate the concentration of X remaining in the aqueous phase after 30.0 mL of 0.200 M X is treated by extraction with the following quantities of n-hexane: a. one 40.0-mL portion. Concentration = b. two 20.0-ml portions. Concentration = c. four 10.0-mL portions. Concentration = d. eight 5.00-ml portions. Concentration = M Σ Σ Σ Σ
Please give me both right solutions.. urgenttttttttt
Please solve this
5. If 0.045 mg of Pb2+ was observed in 1.69 kg of solution what is the ppm?
A stock solution of approximately 7.7x10^-5 molar will be provided in lab. Determine the volumes of each solution needed to prepare 50.00 mL of standard solutions of concentration 0.600x10^-5molar, 1.20x10^-5molar, 2.40x10^-5molar, and 3.00x10^-5molar. Round the calculated volumes to thenearest 0.1mL.
Preparation of sodium standard solutions with concentrations of 10, 20, 40, 60, 80, 100 (ppm) in a volume of 100 ml for each solution. [using a 100 ppm reference solution prepared from a weight of sodium chloride in a volume of 1 liter]
6) A 0.05-mL volume of carbon tetrachloride (CCI) and 0.02 g of p- dichlorobenzene (p-DCB, C6H4Cl₂) are added to a 500-mL separatory funnel containing 300 mL of water and 200 mL of octanol. Calculate the concentrations of both compounds in the octanol and water phases after mixing.
A student was careful to make and stir all of her standard solutions immediately before measuring their turbidity for her calibration curve. However, she let her tap water solutions sit for 10 minutes prior to measuring their turbidity. If she measured the top portion of the solution, would her experimental sulfate ion concentration be higher or lower than it should be?