The distributed load shown is supported by a box beam having the cross-section shown. Determine the maximum value of wo that will not exceed a flexural stress of 12MPa or a shearing stress of 1.20MPa. The distributed load shown is supported by a box beam having the cross-section shown. Determine themaximum value of wo that will not exceed a flexural stress of 12MPa or a shearing stress of 1.20MPa.Wo220mm180mm280mm1mR₁340mm4mR₂

Answered: Image /qna-images/answer/af95da7c-0cc2-4587-bf76-3c187b43f566.jpg

Answered: The distributed load shown is supported…

The distributed load shown is supported by a box beam having the cross-section shown. Determine the maximum value of wo that will not exceed a flexural stress of 12MPa or a shearing stress of 1.20MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam…

A: Given: The width of the beam is 271 mm. The height of the beam is 462 mm. The load Pu is 58.15 kN.…

Q: A laminated wooden beam supports a uniform distributed loading of 12 kN/m. Allowable shear stress is…

A: Consider the free body diagram;

Q: Consider a rectangular cross section with internal transverse shear. Which of the following is…

A: 1.Answer The magnitude of the transverse shear stress is ZERO at the top and bottom fibers of the…

Q: P3 P, P2 A 5-m long, simply supported beam is loaded as shown. Determine the lightest W-shape beam…

A: Given, There is a simply supported beam which is Loaded with point load and Udl as shown in the…

Q: beam has a concentrated load (Pu) at midspan

A: Given: Prestressed beam with fixed ends and having the following properties Beam width = 259 mmBeam…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 4.5 in., d = 4.0…

Q: We constructed a half bridge with two strain gauges in order to capture the effect of maximum normal…

Q: mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the…

A: solution of above problem is below:

Q: A rectangular beam 100 mm x 200 mm carries a uniformly distributed load of 5 kN/m over its simple…

Q: 20 mm 60 mm 20 mm Figure Q4 - Beam Cross-Section ws oz ww 09 20 mm

Q: A simply supported beam is carrying a unıform load. It the beam prop below, what is the final stress…

A: Introduction: Prestress of concrete is basically concrete in which internal stress of suitable…

Q: Q. No. 9: The simply supported beam shown in the Figure supports a uniformly distributed load of w =…

Q: A beam with varying load is shown at the figure below. If the beam properties are given, what is the…

A: Given data: Beam width = 276mm Beam depth = 411mm Span length = 9m Varying load = 18.45 Kn/m Pre…

Q: The steel beam has the cross section shown. The beam length is L = 6.7 m, and the cross-sectional…

A: L = 6.7 m d = 355 mm bf = 205 mm tf = 13 mm tw = 9 mm

Q: The steel beam has the cross section shown. The beam length is L = 7.1 m, and the cross-sectional…

Q: For the beam shown in Fig. Determine the value of the distributed load W if the maximum shear stress…

Q: 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b.…

Q: beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties…

Q: A beam has a uniform dead load and live load has a fixed support at both ends. If the beam…

Q: For the overhanging beam loaded as shown, determine the maximum values of flexural stress and…

A: Answer We know from Bending equation that the Maximum Flexural stress is given by σf,max =…

Q: A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam…

Q: AW310 x 38.7 standard steel shape is used to support the loads shown on the beam in the figure.…

Q: Upvote will be given. Please write the solutions legibly. Solve in 2 decimal place 15 KN 20 KN/m 4m…

Q: The steel beam has the cross section shown. The beam length is L = 7.1 m, and the cross-sectional…

A: Given : L = 7.1 m d = 385 mm, bf = 190 mm , tf = 16mm and tw = 8 mm Allowable bending stress = 250…

Q: Determine the maximum tensile stress σtand maximum compressive stress σc due to the load Pacting on…

A: Given:- P = 6.2 kN, L 5 3.2 m, d =1.25 m,b = 80 mm, t = 25 mm, h =120 mm, andh1 = 90 mm To find:-…

Q: Figure Q6b shows a simply supported 3.75 m long beam with a solid round crosssection and a…

A: Determine the maximum compressive stress and maximum tensile stress.

Q: The beam ABCD with a cross section carries the loading shown in the figure. Determine the magnitude…

A: Find:Magnitude and location of maximum bending stress in the beam

Q: Figure 3

Q: A simply supported beam is carrying a uniform load. If the beam properties are given below, what is…

Q: simply supported beam is carrying a uniform load.

A: Given: Beam width, b = 285 mm Height, d =475 mm Uniform load = 9.1 kN/m Span, L = 13 m Prestressing…

Q: A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 kN as…

A: Given data :- A wooden beam length = l = 1m width = b = 100 mm = 0.1 m height = h = 200 mm = 0.2 m…

Q: E. If the bending stress at section 2 20 MPa. What are the bending stresses at sections 1, 3, and 4.…

A: Bending stress in beam is given by using bending equation,MI=σyWhere, M=bending moment in beam,y=…

Q: A beam has a uniform dead load and live load has a fixed support at both ends. If the beam…

Q: For a square where diagonals are horizontal and vertical, the ratio of maximum shear stress to shear…

A: For a square where diagonals are horizontal and verticalTo find the ratio of maximum shearstress to…

Q: P 2 kN/m 18 mm A D B 0.1 m 0.1 m 0.125 m Figure 5 36 mm

Q: A simply supported beam has a concentrated load at midspan. If the beam properties are given below,…

Q: 2. Find the largest intensity of uniformly distributed load w that can be applied if the allowable…

Q: 2. A beam with an inverted U section is loaded as shown. What is the max flexural stress developed…

A: Given: Required : Maximum flexural stress and shear stress

Q: A rectangular beam 100 mm x 200 mm carries a uniformly distributed load of 5 kN/m over its simple…

A: From a given rectangular beam it is required to calculate maximum shear stress.

Concept explainers

Planar Stresses

Question

100%

The distributed load shown is supported by a box beam having the cross-section shown. Determine the maximum value of wo that will not exceed a flexural stress of 12MPa or a shearing stress of 1.20MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.19 from the support. (MPa) Properties: Beam width = 211 mm Beam height 389 mm 27 Pu 63.66 kN Span of the beam 8 m Prestressing force 326 kN eccentricity = 95 mm
Show FBD and geometry of deformation in solving the problem
The steel beam has the cross section shown. The beam length is L = 7.1 m, and the cross-sectional dimensions are d = 385 mm, b = 190 mm, t = 16 mm, and tw = 8 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 250 MPa. Answer: Wo= WO kN/m
A simply supported beam is subjected to twopoint loads, each P = 500 lb, as shown in the figure.The beam has a cross section of 6 X 12 in. Find thestate of plane stress at point C located 8 in. below thetop of the beam and 0.5 ft to the right of support A.Also find the principal stresses and the maximumshear stress at C.
A beam shown in Figure 7.7 is made of T beam, determine maximum shearing stress develop due to various type of loading. w- 3kN/m A B 2.0m 2.0m 2.0m
UNCRACKED ANALYSIS ON BEAMS
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.4 from the support. (MPa) Properties: Beam width - 211 mm Beam height = 414 mm Pu 73.09 kN Span of the beam = 10 m Prestressing force = 509 kN eccentricity = 130 mm
Beam 9: (P = 26 KN - L = 2.0 metres) For the given cross section of the beam, find the magnitude of the maximum compressive bending stress and also the magnitude of the maximum tensile bending stress. What is the maximum shear stress in the beam and where in the beam does it occur? 2P 2P 25 50 25 25 50 125
Hi, The maximum stress can't be more than 10MPa so that cannot be the right answer. Also where do the figures for 69.5knm bending moment come from?
8
1000 N/m Given: A cantilever beam has loading and cross section as shown. The allowable stress is 64 MPa. 150 mm Determine: the minimum width for the beam 6 m b
An axial load P is supported by the short steel column shown in the figure. The column has a cross-sectional area of 14,400 mm2. If the average normal stress in the steel column must not exceed 69 MPa, determine the minimum required dimension a (in mm rounded to the nearest tenths) so that the bearing stress between the base plate and the concrete slab does not exceed 8 MPa. Assume b = 400 mm.