The disk has a weight of 10 lb and is subjected to a vertical force P = 6 lb and a couple moment M=8 lb ft. The spring is originally unstretched. (Figure 1) Figure 1 of 1 k = 12 lb/ft 1.5 ft A TRESINES M Part A Determine the disk's rotation if the end of the spring wraps around the periphery of the disk as the disk turns. Express your answer using three significant figures. 15. ΑΣΦ. 41 | vec ? Request Answer Ne 0 = Submit Provide Feedback

The disk has a weight of 10 lb and is subjected to a vertical force P = 6 lb and a couple moment M=8 lb ft. The spring is originally unstretched. (Figure 1) Figure 1 of 1 k = 12 lb/ft 1.5 ft A TRESINES M Part A Determine the disk's rotation if the end of the spring wraps around the periphery of the disk as the disk turns. Express your answer using three significant figures. 15. ΑΣΦ. 41 | vec ? Request Answer Ne 0 = Submit Provide Feedback

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft having length equal to 10 m and diameter equal to (50+ 16) mm is simply supported at both ends. The shaft carries four masses (150 + 16) kg, (200 + 16) kg, (250 + 16) kg and (300 + 16) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
Consider the frame shown in (Figure 1). Suppose that w = 410 N/m. Figure 1.5 m y 2m D E 3 m N 3m F 1.5 m B v W 1 of 1 Part A Determine the x and y components of force which the pin A exert on the frame using scalar notation. Express your answers using three significant figures separated by a comma. Ax, Ay = Submit Part B Ba, By = Submit ΑΣΦ Request Answer Determine the x and y components of force which the pin B exert on the frame using scalar notation. Express your answers using three significant figures separated by a comma. < Return to Assignment ΑΣΦ Request Answer ↓↑ vec ↓↑ vec ? Provide Feedback kN ? kN
A shaft having length equal to 10 m and diameter equal to (50+ 16) mm is simply supported at both ends. The shaft carries four masses (150 + 16) kg, (200 + 16) kg, (250 + 16) kg and (300 + 16) kg. These masses are located at a distance of 1.5 m, 2.5 m, 5.5 m and 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m2 and mass density for the shaft material is 7500 kg/m3. Determine critical speed of the shaft in revolutions per minute for the following two cases: Effect of the mass of the shaft is neglected. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
Considering small rotations for the following system, determine the 4 by 4 structure stiffness matrix. Hint: Vertical motion and out-of-plane motion are not allowed. The spring is linear. Rigid weightless bar 01,M₁ 02, M₂ u₁,F1 DOFs for rigid bars: 1,1₂,0₁,0₂ U2, F2
Determine the equivalent spring stiffness of the system using the displacement of the block as the generalized coordinate E = 200 x 10" N/m2 I = 1.6 x 10°m* 6 x 10 N/m 3 m- 2 x 10° N/m m 3 x 10' N/m 5 x 10° N/m
A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (4) the work done by the reaction force of the pin.____________ (J)
CDEFGH is plate with a circular hole in it and has a unit weight p = 2 kN/m². If the initial length of the spring is 1m, find the stretched length of the spring attached at C to the given system. The stiffness of the spring id k=50 kN/m. bwwwww.. 2 m H 0 D X 2 m 2 m G 2 m F E 3m 1m
A bar is attached to the spring at the point C. The left end of the bar is pin supported and can rotates about the pin at Point A. The mass of the bar is m=20kg. The total length of the bar is LAB=3m and LAC=2m. Point A is 0.6 m below the ceiling. A clockwise constant couple moment M= 30Nm is applied on the bar so that the bar rotates from the horizontal position with θ=0° to the vertical position with θ=90°. The spring always maintains at the vertical position. The spring’s stiffness coefficient is k=30N/m and its unstretched length is 0.5 m. The acceleration due to gravity g=9.81 m/s2. During the process that the bar rotates from the horizontal position to the vertical position, determine the following. (2) ) the work done by the couple moment. __________(J) (two decimal places)
The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the elastic force after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
I need handwritten only or i will suggest u to skip becz I'll dislike I'd not handwritten