The diameter and length of single cylinder two stroke gas engine working on constant volume process cycle, are 200 mm and 300 mm respectively with clearance volume 2.78 litres. When engine is running at 135 rpm, the indicated mean effective pressure was 5.2 bar and gas consumption 8.8 m/hr, if Calorific value of Gas used is 16350 KJA m'. Find indicated power developed and indicated thermal efficiency.

The diameter and length of single cylinder two stroke gas engine working on constant volume process cycle, are 200 mm and 300 mm respectively with clearance volume 2.78 litres. When engine is running at 135 rpm, the indicated mean effective pressure was 5.2 bar and gas consumption 8.8 m/hr, if Calorific value of Gas used is 16350 KJA m'. Find indicated power developed and indicated thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
i need anss
THERMODYNAMICS At 2000 RPM, a diesel engine has a diameter of 0.1 m, a strike of 0.11 m, and a compression ratio of 19.1. Each cycle lasts two revolutions and has a mean effective pressure of 1400 kPa on average. Find the engine power i kilowatts and horsepower for a six cylinder engine (Using cold air standard assumption). Show Complete Solution on a Paper.
.
A power generator with two-cylinder, four-stroke gas engine has a bore of480 mm and a stroke of 585 mm. At 300 rev/min the torque developed is10 kNm. The generator is supplied with a mixture of gas and air in theproportion of 1 to 8 by volume. The estimated volumetric efficiency is 80% and the net calorific values of the fuel is 48.6 MJ/m3. Calculate: 1. the swept volume in m3/min, 2. the volume of mixture induced in m3/min 3. the gas flow to engine m3/min4. the energy supplied by gas5. the brake thermal efficiency
Read the question carefully before answering. Box or indicate your final ansurers when solving and draw your diagrams cleanly. Complete solution please. Use 2 decimal places when solving and for final answers. Draw the PV and TS diagram with proper label of points when required. 5. A centrifugal compressor has a single stage and 4 stage model with suction conditions of 100 kPa and 25c. The air must be discharged at 300 kPa. Find the compressor work and heat rejected for each model if the compression is isentropic, and the intercooler pressures.
Q/ Mention 10 applications of internal combustion engines?
An engine break horse power output of 10,000kw for an hour using 2,000kg of fuel per hour and having of L.C.V of 42,000kj/kg. Information:Heat converted into useful work per hour =NKwh;where N the power output in KW=3,600nkj.Heat supplied =M x K. Calculate the break thermal efficiency of the engine
solve asap
Complete the Carnot cycle performed by air if the parameters in points 1 and 3 are the following: Point 1: P_1=2MPa, T_1=600kPoint 3: P_2=120 KPa, T_2= 300K R=287 J/(Kg K)-air only. Please type answer no write by hend.
2. A 10 MW steam turbine generator power plant has a full- load steam rate of 12 kg/kw-hr. Assume no-load steam consumption of as 14% of full-load steam consumption, compute for the hourly steam consumption at 75% load in kg/hr.
Assume a blower operating at 4000 rpm compressing air from 68ºF and 14.7psia to 8.5psig, handling 16000cfm at the design point with an efficiency of 70%. It is desired to find the operating conditions (BHP, H and Q) at 3600 rpm