The diagram below represents the first two stages of a typical AM receiver. the power gains are Ap1=132 , Ap2=0.35 . The input power is Pin =0.77mW 1) Find the overall gain as ratio A, and A,( dB) 2) Find the outputs P, and Pout (unit is mW) 3) Express P1 and Pout in dBm P1 amplifier Ap1 out Pin Mixer Ap2 [HINT : Students should solve the question in a separate paper and fill the answer here (numerical value only no unit ). Also it is must that the student should upload the solved answers in the submission link. Each solved steps carry marks ] 1) A, = A,(dB) = 2) P1 = Pout= 3) P, (dBm) = Pue (dBm) = out

The diagram below represents the first two stages of a typical AM receiver. the power gains are Ap1=132 , Ap2=0.35 . The input power is Pin =0.77mW 1) Find the overall gain as ratio A, and A,( dB) 2) Find the outputs P, and Pout (unit is mW) 3) Express P1 and Pout in dBm P1 amplifier Ap1 out Pin Mixer Ap2 [HINT : Students should solve the question in a separate paper and fill the answer here (numerical value only no unit ). Also it is must that the student should upload the solved answers in the submission link. Each solved steps carry marks ] 1) A, = A,(dB) = 2) P1 = Pout= 3) P, (dBm) = Pue (dBm) = out

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Noise Figure (F) of an amplifier at room temperature is 0.2 dB. What will be the effective noise temperature (Te). Assume room temperature to be 295K.
The capacitance of the resonant converter having fixed value of resonant frequency 65 Hz and inductance of 10 H is pF. In single phase fully controlled converter, if the ripple factor is 2 then the form factor of the converter is
1. Derive the lower cut-off frequency for the basic RC high-pass circuit in Figure 1. R, Figure 1.
Q1) For the identical stages RC coupled amplifier cct. below, where re= 28.480" a. Determine the value of voltage gain for each stage and overall voltage gain for cct. b. Determine fis, fic, and fLE for each stage. c. Determine the low cutoff frequency for the overall cct. e. Sketch approximately the low frequency response for the amplifier overall Vi # 0.47 µF 14 V 268 ΚΩ Cw=5pF C = 12 pF 8 pF C Cwo 5.6 ΚΩ 40 pF Ce = 8 pF 5pF C 12 pF 8 pF C40 pF Ce 8 pF 14 V 14 V Cwo Cw=5pF C = 12 pF 8 pF C 40 pF Ce-8pF Cw, Cw 5.6 ΚΩ 5.6 ΚΩ 0.47 µF 0.47F Vol Vo2 0.47 F Vo H HH B=120 B=120 B=120 HH 28.7 ΚΩ 18.7 ΚΩ 8.7 ΚΩ 10 kn 1.2 ΚΩ 20µF 1.2 kQ. 20µF 1.2 ΚΩ 20µF
I need the answer as soon as possible
None
The diagram below represents the first two stages of a typical AM receiver. the power gains are Ap1=53, Ap2=0.33. The input power is Pin =0.33mW 1) Find the overall gain as ratio AT and AT( dB) 2) Find the outputs P, and Pout (unit is mW) 3) Express P1 and Pout in dBm P1 Pout amplifier Ap1 Pin Mixer Ap2
If vsig is a triangle waveform, determine the maximum amplitude that vsig can have? Showyour calculation.
This circuit represents a small signal amplifier.If C1= 1.5 μF, C2= 0.43 µF Assuming the transistor has: ac current gain =100. dynamic resistance = 100, and Internal Capacitances C= 42 pF, Chc-4pF, C=1pF. 1- Calculate the critical frequencies for the low frequency response. 2- Calculate the critical frequencies for the high frequency response. 3- Write the general formula for voltage gain as function of frequency. 4- Sketch the Bode Plot for the voltage gain magnitude. 2 T mill 1kQ2 O 560 ΚΩ 4.3 ΚΩ C2 HA R1 2 2,7 ΚΩ
k1=35 k2=80
1. If we add a Zero into a system: I. The gain slop will be increased by 20db/decade at its corner frequency. II. The gain slop will be decreased by 20db/decade at its corner frequency. III. Gain will not be affected. IV. None of the above. 2. If we add a Pole into a system: I. The phase will be increased by 90 degrees. II. The phase will decrease by 90 degrees. III. Phase will not be affected. IV. None of the above. 3. In systems, the Integrator add slop to the system gain equal to: I. 20 db/decade. II. -20 db/decade. III. 0 db/decade. IV. None of the above 4. The purpose of the Lag Compensator is: I. Improve the study state response of the close system. II. Speed up the transit response. III. All the above. IV. None of the above. 5. In the Lead Compensator: I. Z > P. II. Z < P. III. Z = P. IV. None of the above.