The device shown is designed to apply pressure when bonding laminate to each side of a countertop near an edge. If a 120-N force is applied to the handle, determine the force which each roller exerts on its corresponding surface.

The device shown is designed to apply pressure when bonding laminate to each side of a countertop near an edge. If a 120-N force is applied to the handle, determine the force which each roller exerts on its corresponding surface.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Related questions

Q: 2.0 m 100 kg 2.0 m 0.5 m 15 m 1.5m The pulley at E is frictionless. Point B is a pinned connection;…

Q: Determine the internal normal force between lettered points on the cable and rod. Draw all necessary…

A: Consider the free body diagram of the joint E as shown below. From the horizontal equilibrium of…

Q: A carpenter holds a 15-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board,…

Q: The device shown is used to straighten bowed decking boards just prior to final nailing to the…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: To find : The forces in members BC, BE, and EF . Free body diagram: The free body diagram is,

Q: The clamp has a rated load capacity of 1500 lb. Determine the compressive force this creates along…

Q: 4.82 Determine the axle loads (normal forces at A, B, and C) for the ore hauler when it is parked on…

A: Draw free body diagram of truck,

Q: Forces F1 and F2 act on the bracket as shown. Find R. F,- 100 N 30 20 F- 80 N

A: The bracket will have reaction force in both x and y-axis as the forces are scattered in random…

Q: 2 m 0.3 m -1.5 m -1.5 m- 12 kN

Q: a d2 d2 d3 F lb B F lb a d1 = 5.19 in %3D d2 = 0.82 in d3 = 0.5 in

Q: Draw a force diagram for the magazine on a magazine rack. Label the force vectors and use equality…

A: The force on the magazine in the above system is shown as:

Q: 5 m 5 m 5m 5 m " 5 m 5m 5 m F₁ F₂ Calculate the support reactions for the pin at E and cable at D,…

Question

The device shown is designed to apply pressure when bonding
laminate to each side of a countertop near an edge. If a 120-N
force is applied to the handle, determine the force which each
roller exerts on its corresponding surface.
C
165 mm-
30 mm
120 N
45
30
mm
45 mm
T

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

F- 10N 250 mm The 10-N force is applied to the handle of the hy- draulic control valve as shown. Calculate the mo- 60 17.5 mm ment of this force about point O.
Also determine the magnitude of the force at O. Express your answer in units of N. Please make sure the answer is numerical value (Do not answer with W).
Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A. Determine the clamping force at A knowing that the force applied to the handle is F = 460 N, and the handle is L = 300 mm long. Enter the magnitude of the clamping force below. Express your answer in N to the nearest whole N. Note that the force F is perpendicular to the handle. 235 mm- 30 mm 30 mm 70 mm E Your written solution must include must include all necessary FBDs and calculations needed to determine the force clamping force at A, the force in member BE, and the forces exerted on member ACD by the pins at C and D.
the tree feller cuts off large trees near ground level and then continues to grasp the trunk. Determine the force in hydraulic cylinder AB for the position shown if the tree weighs 6000lb. Determine the required pressure on the 4.72-in.-diameter piston of the cylinder. draw the free body diagram
Calculate the magnitude of the force acting on the pin at D. Pin Cis fixed in DE and bears against the smooth slot in the triangular plate. 85 mm 200 N B 115 mm 90 mm 140 mm-
Shown below is a toggle clamp that exerts only a vertical clamping force on the wood block at A. Determine the clamping force at A knowing that the force applied to the handle is F = 460 N, and the handle is L = 300 mm long. Enter the magnitude of the clamping force below. Express your answer in N to the nearest whole N. Note that the force F is perpendicular to the handle. A -235 mm 30 mm 30 mm 70 mm O Search OC B 30° F 30 L E Your written solution must include must include all necessary FBDs and calculations needed to determine the force clamping force at A, the force in member BE, and the forces exerted on member ACD by the pins at C and D. MO T
A lug wrench is used to tighten a square-head bolt. If 59-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1.2 in. bolt head so that their external effect on the bolt is equivalent to that of the two 59-lb forces. Assume that the forces are perpendicular to the flats of the bolt head.
Q-4. Determine the "Horizontal Displacement" of Joint "A of the below given frame by using the "Method of Virtual Forces". 6 ft B 200 lb -6 ft- 8 ft
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
Determine the components of all forces acting on member ABCD when qis 0°. A is a roller and B is a pin.You must show any FBDs that you useto solve the problem; use a straight edge to draw please. Include units in your final answer.
give a answer to 3 decimal points
Determine the magnitude of the pin force at B.