The design of the gear-and-shaft system shown requires that steel shafts of the same diameter be used for both ABand CD. It is further required that Tmax $ 60 MPa and that the angle Oo through which end D of shaft CD rotates not exceed 1.5°. Knowing that G= 77.2 GPa, determine the required diameter of the shafts if T= 1350 N-m. 40 mm 100 mm 400 mm 600 mm The required diameter of the shafts is mm.

Q: Consider the tripod shown in (Figure 1). Figure 15m 0.5m 25m < 1 af 1 Part A Determine the magnitude…

A: Determine the magnitude of the moment of the force F= (50i- 23j-80k} N about the base line BC of the…

Q: Like/Thumbs-up

A:

Q: Solve using method of joints.

A: To find force in all members of the truss

Q: 7.59 7% 0.750 1.15 1% % Compute the moment of inertia for the built up section shown below about the…

A:

Q: A solid circular shaft of diameter d and length L is fixed at one end and free at the other end. A…

A: Given a solid circular shaft with, Diameter d. Length L is fixed at one end and free at another end.…

Q: A double bolted lap joint in used to connect two plates of 10 mm thickness using M20 bolt of grade…

A: Joint:Type: Double bolted lap jointPlate thickness: 10 mmBolt:Grade: M20Material: 4.6 (assumed to be…

Q: Using this problem for 9-10. The casting has a mass of 3 Mg. Suspended in a vertical position und…

A: The mass of casting m= 3 Mg = 3000 kgThe upward velocity of casting, v= 200 mm/stime, t= 0.3s

Q: The structural system below using rotational spring + hinge support at joint A and rotational spring…

A: reestablishing force = applied second or force reestablishing force 'T1 = 2Kphi2 +Kphi1' applied…

Q: "Prob. 4.5-16. The aluminum-alloy shaft AD in Fig. P4.5-16 (G= 3.8 x 10 ksi) has a 40-in.-long…

A: Find allowable torque at A (TA)

Q: For the following assembly consisting of three disks A, B, and C: Determine if the assembly is…

A:

Q: Using A992 (50 ksi) steel with KL = 22 ft., determine gPn of the following shape. The channels are…

A: The given data are: Considering a section A992 C10*30 KL=22 ft D=10 in A=8.82 in IXX(channel)=103…

Q: 2. Given: A cover plate (3/4" x 10") is welded to one flange of a W12x45 as shown. Fy= 50 ksi The…

A: Size of plate = 3/4" x 10" W12 x 45  Fy = 50 ksi L = 22 ft or 264 in

Q: Check the adequacy of column AB for applied live load. Fy= 350Mpa W360x51: A= 6450mm2 rx= 148mm ry=…

A: Given: fy = 350 MPa Compression member: W 360 x 51 A = 6450 mm2  rx = 148 mm ry = 38.8 mm d = 355 mm…

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.