The design for a new cementless hip implant is to be studied using aninstrumented implant and a fixed simulated femur. Assuming the punch appliesan average force of 2 kN over a time of 2 ms to the 200 g implant determine (a)the velocity of the implant immediately after impact, (b) the average resistanceof the implant to penetration if the implant moves 1 mm before coming to rest.

Given, punch applies an average force of 2 KN for 2ms. Mass of implant = 200 g.

Answered: The design for a new cementless hip…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

33. A 200kg box is laid down to a rough flat surface whose coefficient of friction is 0.39. Determine the horizontal force needed to accelerate the box at the surface at the rate of 2.5m/s?. a. 1.2610KN b. 1.1463KN c. 1.2652KN d. 1.2052KN
comes to rest from a speed of 72 kmh in a distance of 60 m. By using the principle of conservation of energy, cál- culate the resistive force and the decelera- tion of the car.
Determine the value of the angle α for any impact of a particle on a solid surface, where the entrance angle ѳ is equal to 60 ° and the coefficient of restitution is 0.5 Is it possible that angle α is less than angle ѳ? Why? Please add the free body diagram.
The coefficient of kinetic friction between the60-kg crate and the ground is uf = 0.3. The crate starts from rest, and P = 225 N .(Figure 1) Part A Determine the velocity of the crate when t = 4s Express your answer to three significant figures and include the appropriate units. HẢ v = Value Units Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining • Part B Determine the distance the crate travels when 4 s Express your answer to three significant figures and include the appropriate units. Figure HÀ S = Value Units Submit Request Answer 30° Provide Feedback
Read the problems carefully and provide complete solutions with derivation of formulas (integrals and derivatives. Give complete and neat solution. Use two decimal places for final answers only. Final answers shown below are incomplete. A 900 kg car is sliding down a hill side after the handbrake is disengaged. The hill has a height of 20 m and a 200kg box is placed at the bottom. At what velocity will the car hit the box? What velocity will the box and car have if the collision is perfectly elastic? At what rate is the box moving away from the car, as observed by the driver? 19.81ms; 12.61ms; 32.42ms; 19.81ms
Block A of 500-kg mass is subjected to a towing force F= 2000 t^2 + 3000 t N where "t" is in seconds. If the initial velocity of the block is 6 m/s, determine the velocity after 4 seconds. The block is being towed at a surface inclined at 45 degrees and the coefficient of kinetic friction between these is 0.2. Answer: 106.04 m/s Show COMPLETE STEP-BY-STEP SOLUTIONS and NECESSARY FIGURES to satisfy the answer. Thank you
A 2-kg block travels from the top of a plane inclined 25° with the horizontal compressing a spring at the bottom of the incline with an initial speed of 0.65 m/s. Due to the motion of the block, the spring was compressed by 0.2 meters. The spring has ak of 100 N/m and the coefficient of friction between the block and the incline is 0.40. What is the change in Elastic Potential Energy of the block? O 9.5) O 2.0) O 8.8) O 1.1)
(a) A iron block with a mass of 6.9 kg initially slides over a rough horizontal surface with a speed of 9.0 m/s. Friction slows the block to rest. While slowing to rest, 85.0% of the kinetic energy of the block is absorbed by the block itself as internal energy. What is the temperature increase of the block? (Enter your answer in degrees Celsius.) ?°C (b) What happens to the remaining energy? It is absorbed by the horizontal surface on which the block slides. It vanishes from the universe. It becomes chemical energy. It is so minute that it doesn't factor into the equation.
A heavy goods vehicle of total mass 4.8 tonnes descends a hill with a gradient of 8 degrees from the horizontal. During this motion, the vehicle experiences a rolling resistance to its motion of 880 N. Whilst travelling at a velocity of 72 km/h, its brakes are applied, and the truck is brought uniformly to rest in a distance of 140 m. During this period of constant deceleration, it may be assumed that the rolling resistance remains constant at 880N, this being in addition to the retarding force applied by the brakes. Calculate for the vehicle whilst it is slowing down: a) The vertical height through which it descends. b) Its decrease in potential energy. c) Its initial velocity in m/s. Its decrease in kinetic energy.
A block of weight 800N rests on a rough horizontal surface of coefficient of friction 0.2. It is pulled by a force of 1000N applied at an angle of 300 to the horizontal. Determine the velocity attained by the block after it has moved 30 m starting from rest. Proceed to calculate the further distance moved by the body if the pull is removed.
11th - A rectangular plate with a width of 2 m and a height of 3 m was submerged in water. The distance of the upper edge of the plate from the free surface of the water is 5 m. Since the atmospheric pressure is 95 kPa, what is the hydrostatic pressure force on the plate surface considering the atmospheric pressure? a) 688 kN B) 747 kN NS) 864 kN D) 307 kN TO) 2950 kN
I need it asap

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS