The data pertaining to a stream-gauging operation at a gauging site are given below. The rating equation of the current meter is v= 0.51 N, + 0.03 m/s where N, = revolu- tions per second. Calculate the discharge in the stream. Distance from left water edge (m) Depth (m) Revolutions of a 1.0 3.0 5.0 7.0 9.0 11.0 12.0 1.1 2.0 2.5 2.0 1.7 1.0 current meter kept at 0.6 depth Duration of 39 58 112 90 45 30 observation (s) 100 100 150 150 100 100

The data pertaining to a stream-gauging operation at a gauging site are given below. The rating equation of the current meter is v= 0.51 N, + 0.03 m/s where N, = revolu- tions per second. Calculate the discharge in the stream. Distance from left water edge (m) Depth (m) Revolutions of a 1.0 3.0 5.0 7.0 9.0 11.0 12.0 1.1 2.0 2.5 2.0 1.7 1.0 current meter kept at 0.6 depth Duration of 39 58 112 90 45 30 observation (s) 100 100 150 150 100 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Installed is a venturi meter on a pipe 30 cm diameter in which the maximum flow is 2.7 cum of water in one minute. The throat is 15 cm in diameter. Compute the theoretical discharge that would be passing through the meter when the differetial manometer is as shown. Calculate also the discharge coefficient, C.
Q4-b. For the given data, draw the hydrograph. Separate the base flow. Area of the basin = 40 km. Determine the depth of DRO. Flow (m'/sec) Time (24 hour Flow (m/sec) Time (24 hour format) 2 format) 2 (Next day) 50 110 47 90 8 11 8. 75 75 11 120 70 14 225 14 60 17 290 17 20 23 55 20 270 51 23 140 50
Help me please
Asap
Triangular notch with vertical angle of 90° measures a flow rate. If the value of Cd = 0.6 and there was an error of 2.5 mm in the measurement the head, then calculate the percentage error in estimation of discharge of 21 lit/s.
PROBLEM: Determine he from A toD in the system shown in the figure if the discharge is 1.60 m/s. Assume f= 0.02. 450 mm ø s 600 m 900 mm,90Om 750 mmø, 450 m A C. 4 D GOO mm 720 m (3
1. The performance data of a water pump follow the curve fit Havailable =Ho +aV, where the pump's shutoff head Ho="K", coefficient a="Y" m/(Lpm)?, the units of pump head H are meters, and the units of Vare liters per minute (Lpm). The pump is used to pump water from one large reservoir to another large reservoir at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure. The system curve simplifies to Hrequired =(Z2-Z1)+bV², where elevation difference z2-z1="X" m, and coefficient b = "L" m(Lpm)?. Calculate the operating point of the pump (a) V. operating and (b) Hoperating) in appropriate units (Lpm and meters, respectively). Read the equation carefully. (Zz-Z:) Но b a Y K L 0.0479 4.9 0.029
The following are the data obtained in a stream gauging operation. A current meter with a calibration equation V = (0.32 N + 0.032) m/sec was used to measure the velocity at 0.6 depth. Using the mid-section method, calculate the discharge in stream. Distance from the right bank Depth 0 2 4 6 9 12 15 18 20 22 23 24 0 0.5 1.10 1.95 2.25 1.85 1.75 1.65 1.50 1.25 0.75 0 No. of revolutions 0 80 83 131 139 121 114 109 92 85 70 0 Time (Sec) 0 180 120 120 120 120 120 120 120 120 150 0
سنب Fluid mechanics
Water flows through a Venturi meter as shown below. Determine the discharge coefficient, Cd, of the Venturi meter if the actual discharge is determined to be 2.19 cfs. Use D1 = 12.46 in., D2 = 4.29 in., y = 8.28 in. Points 1 and 2 are centerlines of the inlet and throat, respectively. Round off to five decimal places. Water 2 Di Da Mercury
98.1 kPa EL 47 m EL 35 Butterfly 90° elbows 11. Water is designed to flow in a HDPE pipe of length 267 m as shown in the figure. The flow velocity is limited to 3.3 m/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter and the flow rate. (Ans.: DW: 158 mm, 64.7 liter/s; HW: 153 mm, 60.7 liter/s) Globe
Fluid mechanics