Answered: The cylindrical plug A of mass mA = 2.7… | bartleby

Related questions

Question

The cylindrical plug A of mass mA = 2.7 kg is released from rest at B and slides down the smooth circular guide. The plug strikes the
block C of mass mc = 2.1 kg and becomes embedded in it. Calculate the distances which the block and plug slide before coming to rest.
The coefficient of kinetic friction between the block and the horizontal surface is uk = 0.38 and the distance r = 2.08 m.
Hk
Answer: s=
i
mc
A
MA
B
m

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A lab technician uses a cylindrical projectile launcher to throw rubber spheres horizontally at a nearby vertical target. Using a radar gun, she establishes that a sphere with a mass of 0.150 kg and diameter of 6.00 cm has its speed reduced by 10% due to air resistance when the initial speed is of 46.0 m/s as it travels from the launch site to the target a distance of 18.0 m away. Due to the air resistance, a change in temperature occurs initially only for the air in a cylinder equal to the volume of air swept out by the sphere. Determine the maximum possible temperature change (in °C) for this air when the temperature of the air is 20.0°C. To find the greatest possible temperature change, you may make the following assumptions: air has a molar specific heat of C = = (5) R₁ = molar mass of 28.9 g/mol, and a density of 1.20 kg/m³. °℃ an equivalent
A uniform 10.0 m beam of mass 300 kg extends over a ledge, as in Figure. The beam is not attached but simply rests on the surface. A 60.0 kg student intends to position the beam so that he can walk to the end of it. What is the maximum distance the beam can extend past the end of the ledge and still allow him to perform this feat?
A solid uniform ball with mass m and diameter d is supported against a vertical frictionless wall by a thin massless wire of length L. If the ball has a mass of 45 kg and diameter 32 cm, while the wire has a length of 30 cm, what is the tension in the wire?
2. A cylindrical plug A of mass ma = 0.5 kg is released from rest at point B and slides down smooth circular guide with a radius r= 2 m, as shown in the Figure. The plug strikes the block C of mass mc = 1.2 kg and becomes embedded in it. After the impact plug-block system travel a rough surface S with coefficient of kinetic friction Hk = 0.3. Neglect the air friction for the following calculations. (a) path. Calculate the work done on the plug due to the displacement in the circular (b) Calculate the velocity of the plug-block system just after the strike. (c) Before coming to rest how much distance the block and plug will travels. Also calculate the deceleration rate in this distance.
8
A solid cube of side 2a and mass M is sliding on a frictionless surface with uniform velocity → v as shown in Figure . It hits a small obstacle at the end of the table that causes the cube to tilt as shown in Figure P11.50b. Find the minimum value of the magnitude of → v such that the cube tips over and falls off the table. Note: The cube undergoes an inelastic collision at the edge.
P A person’s arm is held with the upper arm vertical, the lower arm and hand horizontal. (a) Find the center of massof the arm in this configuration, given the following data: The upper arm has a mass of 2.5 kg and a center of mass 0.18 mabove the elbow; the lower arm has a mass of 1.6 kg and a center of mass 0.12 m to the right of the elbow; the hand has amass of 0.64 kg and a center of mass 0.40 m to the right of the elbow. (b) A 0.14-kg baseball is placed on the palm of thehand. If the radius of the ball is 3.7 cm, find the center of mass of the arm–ball system.
Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless wall by a thin massless wire of length L. a) Find the tension in the wire. L m
can you please solve (c) ?
In the figure, a lead brick rests horizontally on cylinders A and B. The areas of the top faces of the cylinders are related by AA= 1.7 AB; the Young's moduli of the cylinders are related by EA= 1.9 EB. The cylinders had identical lengths before the brick was placed on them. What fraction of the brick's mass is supported (a) by cylinder A and (b) by cylinder B? The horizontal distances between the center of mass of the brick and the centerlines of the cylinders are dAfor cylinder A and dB for cylinder B. (c) What is the ratio dA/dB?
4 spheres, each of diameter D= 0.05 m (spheres are identified as 1, 2, 3, 4), are placed on the end of 4 rods of length L = 0.15 m, arranged in a cross pattern as shown in the figure. L The rigid assembly is free to pivot without friction about the axis, o, normal to the page. Sphere 1 is covered with roughness of height ɛ = 0.25 mm while all other spheres are smooth. 1 With an oncoming velocity of U= 60 m/s, which direction will the assembly rotate? (Clockwise or counterclockwise). Use appropriate calculations to explain and justify your answer. Density of air is 1.2 kg/m³ and viscosity is 1.5 x 10-5 m²/s. 3.
answers: Q27) 2.4 Q28) 0.84 Q29) 94KW

SEE MORE QUESTIONS