The cylindrical coordinate robot on a factory's assembly line is shown in a top view (Figure P4.2). The 50 N force acts on a workpiece being held at the end of the robot's arm. Express the 50 N force as a vector in terms of unit vectors i and j that are aligned with the x- and y-axes.

The cylindrical coordinate robot on a factory's assembly line is shown in a top view (Figure P4.2). The 50 N force acts on a workpiece being held at the end of the robot's arm. Express the 50 N force as a vector in terms of unit vectors i and j that are aligned with the x- and y-axes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

H.W.pdf -> Q) A simplified model as shown in figure below of a planar robotic arm. You may assume that each segment has length 1.5 m, and the applied force is 250 N. 0, = 35" and O3 = 0 = 2r. Calculate the moment that the force, F. exerts about the point A. B 0:
4
(a) Suppose you know the coordinates of two points A and B. How do you determine the scalar components of the position vector of point B relative to point A? (b) During the construction of a bridge, a bracket shown in Figure 1 was used to temporarily hold two cables FA and Fg = 600 N. After a while, you noticed that the bracket is shaking and slowly being pulled out of the wall by the cables. Given that e = 20°, find the resultant force and its direction counter clockwise from the positive y axis. FA 700 N 30 A Figure 1
Figure Q1c shows a bracket on rollers that allow the bracket to move along a beam in the horizontal direction. A force F₁ of 2625 N acts at point A where the angle between F₁ and the x-axis is 100. If force F2 acts at an angle a = 40° between F2 and the y-axis: (1) (ii) Give your answers to the nearest newton (N) to 2 decimal places. Assume coplanar forces and assume horizontal rolling is frictionless. Determine the magnitude of F2 necessary to maintain bracket on horizontal equilibrium. Determine the vertical force at A acting along the y-axis. F1 0 y α Figure Q1c F2 X
Could you walk me through these two problems
The figure shows a person wearing weight boots and doing lower leg flexion/extension exercise in a sitting position to strengthen the quadriceps muscles and a simple mechanical model of his leg. W1 is the weight of the lower leg, W0 is the weight of the boot, the magnitude of the pulling force applied to the tibia by the quadriceps muscles through the FM patellar tendon, the magnitude of the reaction force acting on the FJ tibiofemoral joint. Point O is the center of the tibiofemoral joint, point A is the point where the patellar tendon attaches to the tibia, point B is the center of gravity of the lower leg, point C is the center of gravity of the weight boot. The distances between point O and points A, B and C were measured as a=12 cm, b=24 cm and c=36 cm, respectively. The angle that the long axis of the tibia makes with the horizontal is β=39°, the angle between the line of action of the quadriceps muscle strength and the long axis of the tibia is α=16°. Points O, A, B and C lie…
Needs Complete typed solution with 100 % accuracy.
3.9 The linkage in Fig. 3-10 has 0,A = 8mm, AB = 19. 3mm, AC = 13. 3mm, and offset = %3D 3. 8mm. The crank angle in the position shown is 34. 3° and ZBAC =38. 6°. Find wz, vA, VB, Vc for the position shown for w, = 15rad/s in the direction shown. ( Choose two methods) 1) Use the velocity difference graphical method. 2) Use the instantaneous center graphical method. 3) Use the analytical method. @2 B offset 02 Fig. 3-10
Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please
I need the answer as soon as possible
Figure 1 (ii) For the system shown in Figure 2, determine (i) the required value of a if resultant of three forces is to be vertical and (ii) the corresponding magnitude of resultant. 200 N CX Figure 2 Ja 30⁰ 150 N 100 N
1. Please refer to the following vectors:A = 6i + 2j - 3kB = 3i - j - 2kC = -i + j - 4kD = j - 3kE = -i + 2kF = -5kG = 2iH = -3jI = -4i +4j Two airplanes started drifting away from the origin along the directions of displacement vectors {B} km and {E} km respectively. If vectors B and E are their position vectors in rectangular coordinate system after some time t, what will be their separation distance in kilometers? 2. A ball is speeding up along a circular track. What can be said about the velocity and acceleration vectors on the body? 3. In an intersection, a bus moving at (100i) m/s and a truck moving at (200j) m/s collided with each other. Assuming that the two objects have the same mass, what would be their final speed together?