The cylinder and the block are connected by a horizontal cord. Determine the largest couple C that can be applied to the cylinder without disturbing the equilibrium of the system. Assume that both bodies are homogeneous. 3 in. 3 lb 5 in. 3 lb -Hj = 0.35

Q: termine the critical path by filling the table below  What is the length of this project in days?…

A: To find: The critical path and the length of the project.

Q: 4) Select ALL choices which may be indirectly controlled by Surface Profile IF NO DATUMS ARE USED A…

A: Surface Flatness  Perpendicularity

Q: Choose the right answer:   a)The lower the quality of the surface finish, the less of area of a…

A:

Q: Q11. Original design may not be A. New working principles B. New idea C. New concept D. New…

A:

Q: Name 4 performance indicators and targets for the maintenance department/section

A: This question is based on the concept of maintenance of machines and equipment.

Q: Indicate the following technical tolerance requirements in Fig.3. a) The diameter of the middle…

A:

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A:

Q: 2. Before developing possible solutions, an engineer usually _________________. A. communicates his…

A: Before developing possible solutions, an engineer usually _________________

Q: List the proper sequence of the Engineering Method of Problem Solving and defineidescribe each.…

A: Engineering method of problem solving: Identify the problem Analyze the problem List the solutions…

Q: Which one of the following type of benchmarking is least likely to resuit in any major breakthrough…

A:

Q: You are applying for a job in mechanical design and system company, where you have been required to…

A: Misalignment occurs when one surface or shaft is forced to deviate from its desired position.…

Q: c) Evaluate the performance of Static Cone Penetration Tests

A: The Static Cone Penetrometer is utilized to assess the consistency of soils, their level of…

Q: Mention examples of problems in real life, in which some characteristic or parameter can be applied…

A: Controlling or improving a specific characteristic or parameter is crucial for achieving the desired…

Q: 6 Which one of the following semi-destructive technique is used for measuring residual stress? a)…

A:

Q: Perform FMEA and Root Cause Analysis for any TWO problems faced in your industry.

A: introduction; FMEA is a failure mode and effect analysis. FMEA quality tools enhance the quality of…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: This is still the wrong answer for McGraw Hill. Each answer I try is wrong, so not sure if I'm doing…

A:

Q: he several disadvantages as com

A: Answer given below.

Q: uestion 8 Which of these is an important design consideration in engineering design? Select one: O…

A: Solution.jpg

Q: What would be the critical path and the project duration for M?

A: The network diagram has activities from A to M and different time intervals are given.

Q: Choose the assumption made for using this FBD.

A: (ii) Answer = (a) explanation = for the FBD of the crate, the assumption that has to be made is that…

Q: Drilling and Completion Engineering II An exploration well is to be drilled to a total depth of…

A:

Q: H.W.#(2).. Surface treatments can be divided in three sectors that are : 1- Surface Engineering to…

A: 1.surface engineering to change surface metallurgy  Thermal spraying

Q: 50. If an asset is operating with an availability of 98% at a performance rate of 84%. What is the…

A:

Q: 4@4m 16 m b 12 kN 2 m 3 m

A: According to Bartleby QnA guidelines, “Since you have asked multiple question, I will solve the…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Only one of the following is correct. Select the correct answer. Continuous process production has…

A: Given: Multiple choice question

Q: please provide a type written explanation of the topic

A: Solution : Need for us to generate straight line motion

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: Q1) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3)…

A: Define the Following The stress and the strain Yield strength Tensile Strength Modulus of elasticity…

Q: Explain the life cycle assessment methodology

A: Life cycle assessment : Life cycle assessment it is define as it is the factual analysis which is…

Q: 3 Under what circumstances might an employer need to maintain an OSHA injury/illness Jog for nersons…

A: The Work-Related Injuries and Illnesses Log (Form 300) is used to classify work-related injuries…

Q: I am not able to see the answers can you please write it in a paper

A:

Q: Provide a detailed breakdown of the safety and learning features included into the set.

A: It is asked to provide a detailed breakdown of the safety and learning features included in the set

Q: Gas welding process creates a messy work piece. Select one: True False

A: True In gas welding process oxy acetylene gas combustion take place and heat produced is utilised…

Q: Which machine would you recommend given the following information and interest rate is 10%? New Used…

A: Given data as per the question  Interest rate = 10% Calculations considering 1st machineInital cost…

Q: The track curves on the Transnet railway line between Belfast and Steelport in the Limpopo province…

A: Given: Track curves are heavily corrugated between Belfast and Steelport  Requirement: Explain how…

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: Q/ Discuss briefly on materials selection for wear resistance

A: The process of designing any physical thing includes the choice of materials. The major objective…

Q: Don’t use ai

A: Step 1: a) Penetrant testing, Magnetic particle testing can be used. Compared to Other NDT methods,…

Q: I need help solving problems 13, 14, and 15 pertaining to the print provided below.

A: 13.Dimensions of the same object should not be copied or we can say that the same information should…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.